Thingiverse
µDiva by Tomtortoise
by Thingiverse
Last crawled date: 3 years ago
This project requires a lot of close quarters building and soldering, it will probably be a bit frustrating to build so be aware
These are the files for making the frame of the Micro Diva. It requires 7x regular brackets, and one of each of the other parts. There are two options for the back plate, one that has a hole for a 4 pin mini XLR, and one with no hole to give options for the USB wire. The face plate area surrounding the touch slider gets raster cut about 1-1.5mm deep to allow the touch slider to set into the face. the uDiva logo is also set in to be painted but that can be removed or changed if you would like.
There are two brackets that need to be printed for holding the slider in place.
You will also need the following parts to complete the build.
7X 1/4(6.35mm) buttons
4x Seimitsu PS-14-DN buttons of your color choice
1x Brook PS3/PS4 Fight Board PCBA
1x Brook Touch board (eBay usually has them, looks like the green PCB center top)
1x USB cable (4 pin mini XLR male and female optional)
1x Pack, M2 bolts 12mm
1x Pack, M2 bolts 8mm
1x Pack, M2 nuts
These are the files for making the frame of the Micro Diva. It requires 7x regular brackets, and one of each of the other parts. There are two options for the back plate, one that has a hole for a 4 pin mini XLR, and one with no hole to give options for the USB wire. The face plate area surrounding the touch slider gets raster cut about 1-1.5mm deep to allow the touch slider to set into the face. the uDiva logo is also set in to be painted but that can be removed or changed if you would like.
There are two brackets that need to be printed for holding the slider in place.
You will also need the following parts to complete the build.
7X 1/4(6.35mm) buttons
4x Seimitsu PS-14-DN buttons of your color choice
1x Brook PS3/PS4 Fight Board PCBA
1x Brook Touch board (eBay usually has them, looks like the green PCB center top)
1x USB cable (4 pin mini XLR male and female optional)
1x Pack, M2 bolts 12mm
1x Pack, M2 bolts 8mm
1x Pack, M2 nuts
Similar models
thingiverse
free
Anker 4 Port USB Hub 90 Angle by TecHno_Guy
...ugh they are optional.
parts needed:
1x anker 4 port usb hub
parts optional (but recommended):
1x m2 countersunk screw
1x m2 nut
thingiverse
free
Button Box for USB Controller by TwistedStick
... controller by twistedstick
thingiverse
16 button face plate 13mm holes. lower has pad to mount pc board and hole for usb cable.
cg_trader
$5
8 Input Audio Snake Box | 3D
...snakebox-faceplatev1.stl - audiosnakebox-faceplatev2.stl audio box snake studio microphone mic xlr trs audio device cable gadgets
thingiverse
free
Micro Servo Claw by FelixFoundSheep
... receiver
1x remote control
1x 5-6v battery pack
7x m3 bolts (12-16mm length)
7x m3 nuts
7x locking washers (optional)
7x washers
thingiverse
free
SimLab Vertical Mount Facia USB Mount by RCHeliGuy
... or very small screwdriver can help to center the nuts.
the usb mount takes 4 x m3x20mm bolts and locknuts to secure the din face
thingiverse
free
PSE USB mount for SimLab Vertical by RCHeliGuy
... or very small screwdriver can help to center the nuts.
the usb mount takes 4 x m3x20mm bolts and locknuts to secure the din face
thingiverse
free
QU-BD One-Up / Two-Up Extruder Fan Bracket by MacAttak
... 10mm m2 bolt, and a m2 hex nut.
attaches via the m2 bolt to an unused mounting hole in the bottom of the extruder (see photo).
thingiverse
free
Two piece Mega Zero enclosure for Creality v4 board or SKR Mini-E3 by ksanislo
...ional hole for a kill switch button has been added. i used these buttons from amazon but most 1/4" buttons should fit fine.
thingiverse
free
Arduino Nano v3.0 Casing
...ional: hot glue the end before installing button in its hole - this can be a mess, hot glue never stays where you want it to go!)
thingiverse
free
Creality CR-5 Pro - BTT SKR MINI E3 V2.0 support plate by FlorianKinder
...x) m3*8 screws (attach the plate to the chassis)
5x m3*12 screws (controller)
4x m2*12 screws (raspberry)
4x m2*12 screws (relay)
Tomtortoise
thingiverse
free
Mad Max Shotgun Spacer by Tomtortoise
...ortoise
thingiverse
use these parts to replace the stock ones on your mad max airsoft shotgun in order to use the madbull shells
thingiverse
free
Leather Card Wallet by Tomtortoise
... for assembly yet but i am providing the files to laser cut your own pieces.
post on my website for this project and more is here
thingiverse
free
5.1 Hi-Capa Magazine Base by Tomtortoise
...tm, kjw, we, and any other 5.1 magazine. ever drop a mag on the ground? print one of these to replace your cracked one, or seven.
thingiverse
free
Hi-Capa Short Magazine Base by Tomtortoise
...he original and the other is a simplified easy to print version. no post print work is needed other than picking off extra blobs.
thingiverse
free
Airsoft Tracer V1.1 Case (Prototype Project) by Tomtortoise
...v2 so i can make kits and possibly make this an open source project with free to use boards, schematics, and a bill or materials.
thingiverse
free
Nintendo Switch Laser Engrave Template by Tomtortoise
...o import into other image programs of your choice
make sure to not vector cut when using the laser as that will slice your switch
thingiverse
free
Project Diva FT/CT PS4 Arcade Controller (Laser Cut) by Tomtortoise
...ic is nice)
1x controller face
1x center face bracket
1x back wall
1x back wall
2x side walls
8x corner brackets
8x face brackets