Thingiverse
RC Boat - Pump Jet Boat / 遥控船-喷射泵 by N7_Cat
by Thingiverse
Last crawled date: 3 years, 4 months ago
I'm going to preface this by saying that I have no experience in boat design or RC in general. That being said, I am an engineer and I think I figured most of it out...if boat flips, porpoises, or otherwise does a barrel roll don't say I didn't warn you :P. If it does any of the above and you are a clever kitteh and have some tips based on real experience feel free to help me out. I've added air cooling via vortex intakes that "should" eject any water spray. I couldn't decide if the boat wanted to be a trimaran, rigger boat, flat bottom, ground effect vehicle or stepped hull V so I mashed it all together in an unholy union of boat design sacrilege - your welcome.
I modeled water displacement and Fusion 360 calculated the mass, because it is such a narrow hull it is critical to keep the print weight low and rely on the carbon fiber tubes for most of the strength. I am targeting a total weight around 600 grams for everything, motor and batteries included. Printing with low layer count (maybe even single) / low infill should reduce the mass of the boat to acceptable levels, using flexible primer or maybe plastidip on the finished boat should help with water tightness. I'm still experimenting with my prints, I'll let you know results and recommended print settings for each section once finished.
The 2212 motor is a marvel to me, how is something so awesome so affordable? I wanted this boat to be affordable first, performance is secondary. While an outrunner is atypical for boats I think I've designed out the cooling issue via internal airflow and motor cooling impeller. Besides yeeting boats around at 200kph seems like a dangerous way to accidentally impale swimming googies...a project for another day.
Scroll down to post processing pictures for detailed build instructions - currently updating. Certain components can only be installed before melding of the hull sections including the completed battery packs and motor - do not glue hull together before all components are fitted.
Josh at Flite Test did a good vid about waterproofing RC electronics with Peter Sripol (Flite Test | Waterproofing Electronics)
11/6/2020 Performed a submersion test with sanded model - due to the way walls interface with fill there is capillary action between the individual lines of printed material at the base of the sponsons. This causes water to slowly seep into the model. As I plan on priming the boat, hydro dipping, clear coating then waxing these four layers should seal off the capillary gaps. A couple coats of flexible primer would probably do the trick - focus more primer on the flat surfaces that serve as the first layer of Boaty and McBoatface prints. If you plan on running your boat without these coatings I've read that brushing or submerging in melted candle wax (not too hot though - Paraffin starts melting at 37 deg C / 99 deg F) can seal a 3d print, if you are a motorcyclist you likely have a can of Maxima chain wax (best chain lube ever :) - this is essentially parrafin wax with some additives in a carrier fluid and can likely serve the same purpose without the messy melting (though I'd be concerned if any of the additional additives would leach into the water). Along the same thought process I'm thinking that carnauba car wax would likely work too though be less durable. Btw if you do use wax keep fire safety in mind as some FDM plastics are flammable and wax has now made it even more flamable. Another method that I've seen RC airplane makers use for waterproofing is to coat model in a very very thin layer of gorilla glue - it doesn't bubble up too much if the layer is thin enough. A waterproof wood glue like titebond might even work - I'm not sure how well it would adhere to FDM polymers. If anyone in the RC community has any suggestions they would be welcome - maybe when you post your make you can let us know how you waterproofed your model :). I'll post pictures of my own process soon.
BOM:
Motor: 2212 Though, with some work, you can now use an alternate motor with the custom motor plate template "Custom Motor Plate Template.stl" (Dimensions center to center between the 3 mm mounting holes are 49 mm X 23.41 mm. The top surface of the mounting plate (measured from the large flat area not the post) is 18.738 mm below the center-line of the propeller axis). Keep weight and cooling considerations in mind if using an alternate. If using the 2212 just download the original 2212 Motor Mount. (I don't have enough experience to say what KV level is ideal, I am leaning towards lower KV motors as they deliver the same torque at lower amps with higher KT values. We like KTs - get it...KTs?) https://www.aliexpress.com/item/32672300112.html
ESC: SimonK 30A 4S with BEC (you will need to seal or find an alternate water proof ESC) https://www.aliexpress.com/item/32308790386.html
Prop: 32mm with 100 mm shaft (note get the 10 cm one with 3.18 motor as the 2212 shaft is 3.175 mm - I initially tried to model an axial flow impeller but I found this purchased item to be far more sturdy. Advantages are it has built in high speed bearings and replacement props can be purchased from here as well. I also added provisions for a diy 3mm shaft using 623 bearings) https://www.aliexpress.com/item/32714017489.html https://www.aliexpress.com/item/32528668718.html
Servo: 9g servo (important you will want to waterproof or find an alternate waterproof servo) https://www.aliexpress.com/item/33005962141.html
Reinforcement: 6 mm OD 4 mm ID Carbon Fiber Rods https://www.aliexpress.com/item/32310771446.html
Power Source (btw if, like me, you are inexperienced with RC make sure to inform yourself about some of the precautions needed with lithium based batteries especially around charging and storage. Unlike your consumer electronics the LiPo cell is very much exposed in RC and special care must be taken. RC Review and FliteTest do some good youtube vids on the matter) :
Cat Grumpiness
3S LiPo power pack (I was able to find a 1300 mAh one that fits well 3S 1300 mAh 60C LiPo 75 X 34 X 24 mm - The maximum extents of a battery able fit in the front of the boat are 82 X 36 X 26 mm if removal is not needed)
18650 batteries are no longer being supported, battery compartments are left in but I've come to the conclusion that its just not a good idea..I originally thought it would be cheaper owing to relatively inexpensive cells and BMS modules but once you add a constant current power supply for charging, nickle strip welder, and discharge rate / weight / C.G considerations LiPo starts to make a lot more sense...never mind the potential effects of water on Li Ion cells...
Receiver and transmitter: Up to you (and your local regulations), I'm using a Flysky FS-i6X transmitter and FS-GR3E Waterproof receiver (note i6X will need to be in AFHDS mode to work with FS-GR3E) https://www.aliexpress.com/item/32785968777.html https://www.aliexpress.com/item/32892188833.html
M3 X 6 X 5.3 Embedded Nuts (old link no longer works - possible substitution M3 X D5 X L6) https://www.aliexpress.com/item/4000232858343.html
M3 Machine Screws (Button head and Flat head) https://www.aliexpress.com/item/32798146322.html or stainless https://www.aliexpress.com/item/32934186482.html
XT60 connectors, 3.5 mm bullet connectors, grease (marine), filament material compatible glue. The connectors are sold by the same storefront as much of the material above.
Sound system: Bongo Cats
Tentative Print Settings (Cura has a setting under Travel called combing mode which helps reduce stringing in the inaccessible interior). Personally I'm printing in PETG but ABS or ASA might be a good options too if you are setup for that with enclosure and ventilated space (due to easier gluing / reduced density - if using ABS or ASA I would advise against acetone smoothing as thin walls will likely deform). I excluded PLA as it is not as temperature / weather / UV resistant as the above materials and will swell / deteriorate in water unless waterproofed. I print at 30 mm/s or less but it might still print well at more default speeds of 60 mm/s. Thrust vector nozzle and 2212 cooling impeller will be printed in TPU for its reliable layer adhesion as both components will be subject to cyclic loading and high shear stress. STL files are already saved in as print orientation.
PETG/ABS/ASA Parts
Boaty (PETG/ABS/ASA): 0.4mm nozzle, 0.15mm layer height, 1 walls, 3 bottom layers, 3 top layers, 14% grid infill, supports on overhangs over 80% touching buildplate (apx 116 grams)
McBoatface (PETG/ABS/ASA): 0.4mm nozzle, 0.15mm layer height, 1 walls, 3 bottom layers, 3 top layers, 14 % grid infill, supports on overhangs over 80% touching buildplate, brims are helpful for ensuring support adhesion (apx 218 grams)
Cover: TBD (PETG/ABS/ASA) 0.4mm nozzle, 0.15mm layer height, 1 walls, 3 bottom layers, 3 top layers, 14% grid infill, supports on overhangs over 60% touching buildplate (apx 12 grams)
2212 Motor Mount (PETG/ABS/ASA): 0.4mm nozzle, 0.15mm layer height, 5 walls, 3 bottom layers, 3 top layers, 25% grid infill, supports on overhangs over 80% touching buildplate, brims are helpful for preventing warping (apx 30 grams)
Ride Plate: (PETG/ABS/ASA) 0.4mm nozzle, 0.15mm layer height, 5 walls, 3 bottom layers, 3 top layers, 25% grid infill, supports on overhangs over 80% touching buildplate (apx 6 grams)
Servo Hatch: (PETG/ABS/ASA) 0.4mm nozzle, 0.15mm layer height, 4 walls, 3 bottom layers, 3 top layers, 100% infill, supports on overhangs over 80% touching buildplate, Brim (apx 2 grams)
TPU parts
Thrust Vector Nozzle: (TPU) 0.4mm nozzle, 0.15mm layer height, 3 walls, 3 bottom layers, 3 top layers, 25% cubic subdivision infill, supports on overhangs over 80% touching buildplate (apx 15 grams)
Stator Bowl: (TPU) 0.4mm nozzle, 0.15mm layer height, 3 walls, 3 bottom layers, 3 top layers, 25% cubic subdivision infill, supports on overhangs over 80% touching buildplate (apx 24 grams)
Cooling Impeller: (TPU) 0.4mm nozzle, 0.15mm layer height, 2 walls, 4 bottom layers, 4 top layers, 100% concentric infill, (apx 2 grams). Note this part narrows to a single wall of 0.4mm TPU - slowing down print speed drastically (15 mm/s) is likely needed for successful print
Motor (50 grams), LiPo (129 grams) (18650s are out), ESC (28 grams), servo (9 grams), and receiver (6.5 grams)
A note for early downloaders: I tend to iterate and reiterate a design multiple times before I'm happy with it. Designs subject to change...frequently...
N7 Cat Says: "Dis my bigges and shiniest objec yet, 2020 u cray cray, I jus gonna yeet away from u in mah boat wif mah other kitteh fiends"
Updated: 9/28/2020, Updated files Boaty and Cover, added provisions for gluing a 5mm X 2mm magnet on the cover and boat for magnetic latching
Updated: 9/29/2020, fixed a problem with McBoatnose missing modeled tube for carbon fiber reinforcement.
Updated: 10/2/2020, added a custom motor plate "McBoatface Custom Motor Plate.stl" for anyone wanting to use a motor other than the 2212. Intent is that you will be able to model your own motor housing (and share with others along with recommendations for ESC and battery :) for mounting onto the flat plate. 3 mm dia screws will secure the motor mount to the two sections of the boat, as the mount will be subject to vibration fastening hardware (embedded nuts or lock nuts) is recommended in your design. Like the original requires brims and supports.
Updated 10/4/2020, added battery holder compartments along the length of the hull for an integrated 3S 2P 18650 setup. I'm planing on spot welding the batteries together with pure nickle strips and wiring to BMS. Note there are two battery caps (non symmetric). Added a baffle near the motor cooling impeller to improve airflow and cooling. Additionally minor improvements to printability around the servo mount and filleting of vortex outlet. For custom motor users new battery holders and air baffle might interfere with especially big motors but you can model / clip them out if needed.
Updated 10/6/2020, added built in support for servo hatch opening, improved joints between the three boat hull sections by adding grooves and other features for the expanding polyurethane glue to latch onto. Fixed a printability issue with the fillet that supports the propeller shaft. Started first print of the boat section, may update if issues crop up after print finishes.
Updated 10/7/2020, added a channel in the battery compartment to allow for wire to be routed through.
Updated 10/8/2020, post printing improvements, increased diameter of battery compartment, prop shaft and carbon fiber shaft openings. Improved servo hatch support structure to make it easier to remove.
Update 10/9/2020, Estimated static resting position of the boat in water and calculated rough target mass for finished boat. After a print failure of the protective grid on the intake as well as impact durability test failures I have replaced with a filament heat stake method as shown below in post processing pics.
Insert 1.75 mm filaments into the slots and use a low temp soldering iron to melt the ends into the inlet - you could also use servo wire and glue in place...unless you like grinding baby fish into a pulp...u monster
Updated 10/11/2020, with 18650s looking like less and less of a good idea and mass being more of a concern I trimmed the battery compartments down to two 0.4 mm walls. This reduces mass and print time dramatically.
Update 10/11/2020, realized I derped and forgot to add an access port for servo wiring. I've created an access port on the battery compartment closest to the servo wire (port/left side). As there were some unbridgeable overhangs I made some built in supports that need to be pried or clipped out before use.
Update 10/12/2020, created an alternate path for servo wire on the top of the baffle in case I decide to house all electronics in the cover. After fighting with carbon fiber tube on second print increased the diameter of the carbon tube channel and started printing again :P Ever had a carbon fiber sliver? I haven't nor do I ever want to...make sure to wrap the end of the tube that you are handling in masking tape or something to protect your hands
Updated 10/14/2020, minor improvements to Boaty and McBoatnose to reduce support generation. Trying some new tricks to strengthen servo mount and embedded nut support by creating additional walls in those areas. Improved airflow on McBoatnose 2212. Updated the stator bowl as supports were not properly generating - something to do with angle of one of the pieces aligning with support autogenation void
Updated 10/15/2020, McBoatface 2212 motor mount was a bit of a tight fit, adjusted motor mount. Adjusted joints between sections
Updated 10/16/2020, added receiver tray and antenna port to cover
Update 10/18/2020, added mounting points for turn fin in case they are needed - I couldn't find any info on whether one would be needed for a pump jet nor dimensions for standard mounting points. Converted the fixed ride plate to a variable trim ride plate using 1.5 mm servo wire as the adjustable retention mechanism. Backup retention provided by an embedded nut and M3 X 10 screw + spring. Joint held by filament joint
Updated 10/20/2020, some weird artifacts were cropping up in cooling impeller during slicing, increased to high resolution stl and fixed wall width. Encountered a problem with McBoatnose tips coming off due to single walls and how narrow it becomes. Blunted the tips. Also had to physically clip some of the joints between front and mid section in order to get it to fit, adjusted the model so this is not required. Carbon Fiber tubes now provide most of the support between the front and mid section. Created McBIGface for those of you with Z axis build volume above 280 mm so you can print mid and front sections as one piece #jealouscat (note that this will result in a weaker motor mount as you will still need to balance weight considerations with strength requirements - play around with slicer settings starting from McBoatnose as a baseline)
Updated 10/21/2020, increased prop clearance in stator bowl
Updated 10/22/2020, Major overhaul...N7 cat shredded all the toilet paper...McBoatface and McBoatnose now one part, motor mount now modular for both 2212 and custom motors, added a custom motor mount template, increased sponson size 25%, other minor improvements
Update 10/24/2020, tried to reduce weight of McBoatface by hollowing out the sponsons, turns out a solid object with grid infill doesn't contribute much to weight...who knew...saved 5 grams!
Update 10/26/2020, realized that the cover / McBoatface interface would allow water to seep in at the front seam, updated these two parts to improve water shedding in this area. Added a part called Compatibility Shim For Pre Oct 22 Update Boaty Prints.stl which will allow any prints of Boaty made prior to 10/22 update to be used with new McBoatface
Update 10/27/2020, major iteration work completed - only minor changes from this point on - latest files re-uploaded to sync with my local files. Post processing instructions will be completed once prints are completed
Update 10/28/2020, vortex was breaking during print, strengthened the part with additional walls
Update 11/4/2020, updated servo hatch (missing cutout for gear)
Update 11/5/2020, work in progress status lifted - no major issues encountered during assembly
Updated 11/6/2020, after dropping my completed boat noticed one of the sponsons cracked ;.; strengthened the sponsons with option to add 200 mm carbon fiber tube reinforcement (adds ~35 grams to total weight inc carbon tubes or ~ 15 grams without carbon reinforcement). Thanks to a helpful tip from the community I have added a 5 degree pitch up to the thrust vector nozzle - if your boat has a nose down attitude and the ride plate adjustment is not enough this should hopefully correct that. There is a moment force applied by the thrust which pushes the nose down, this minor tweak will hopefully apply a slight corrective force which allows the boat to get on stable plane. Added a ride plate servo wire retention slot to stator bowl. Increased McBoatface carbon tube clearance. Added a 10 deg pitch nozzle in case 5 deg is not enough, as I'm still waiting on batteries to arrive I haven't had a chance to perform test to determine which will be best. Performed submersion test and posted results near the top of this summary
Update 11/8/2020, moved the Boaty magnet catch to the top surface instead of underside to improve ease of assembly. Closed the opening in the baffle since servo wire was long enough to not need it. Moved the cover magnet closer to the Boat magnet to improve latching strength. Improved McBoatface by filleting the sponson to wing interface and creating water rejection channels near the vortex exits.
Update 11/15/2020, added a version of cover with provisions for 3mm LED navigation lights
Update 11/18/2020, first functional test of the waterjet, I found that even with TPU gasket air and water would spray out thus sealing the stator bowl to boat body with silicone or glue is necessary. I found an issue with air locking - I don't fully understand the cause but experimentally determined a way to resolve this via a pending modification to the thrust vector nozzle. Update uploaded (Thrust Vector Nozzle Variable Pitch) but untested - I'll hopefully get a chance to print and test by tmw. Testing confirms the air lock issue is resolved with this new nozzle - there is some loss of efficiency. I don't really know why this fixes the air lock but I suspect the stator bowl fins were not redirecting enough of the rotational energy generated by the prop resulting in an area of low pressure which would draw air in from behind the outlet...without high speed cameras or CFD I can't really say. N7 Cat says "wut he trying 2 say iz I putz mah paw ober da nozzle and dat fixes it"
11/21/2020 did some more study on propulsor units and updated the pitch and number of stator vanes - 5 vane stator uploaded - will test later and delete original if testing displays improvement. Test showed marked improvement in both trust and elimination of air lock using the 5 vane stator - original deleted. For anyone else designing or trouble shooting other pump jets on thingiverse the number of stator vanes needs to be a prime number and different than the number of prop blades otherwise a standing wave can develop. At some point in the future I might experiment with a properly designed axial flow prop and stator - salt sintering might be able to create a strong enough part for use as a prop.
11/25/2020 reverted thrust vector nozzle to neutral pitch
I modeled water displacement and Fusion 360 calculated the mass, because it is such a narrow hull it is critical to keep the print weight low and rely on the carbon fiber tubes for most of the strength. I am targeting a total weight around 600 grams for everything, motor and batteries included. Printing with low layer count (maybe even single) / low infill should reduce the mass of the boat to acceptable levels, using flexible primer or maybe plastidip on the finished boat should help with water tightness. I'm still experimenting with my prints, I'll let you know results and recommended print settings for each section once finished.
The 2212 motor is a marvel to me, how is something so awesome so affordable? I wanted this boat to be affordable first, performance is secondary. While an outrunner is atypical for boats I think I've designed out the cooling issue via internal airflow and motor cooling impeller. Besides yeeting boats around at 200kph seems like a dangerous way to accidentally impale swimming googies...a project for another day.
Scroll down to post processing pictures for detailed build instructions - currently updating. Certain components can only be installed before melding of the hull sections including the completed battery packs and motor - do not glue hull together before all components are fitted.
Josh at Flite Test did a good vid about waterproofing RC electronics with Peter Sripol (Flite Test | Waterproofing Electronics)
11/6/2020 Performed a submersion test with sanded model - due to the way walls interface with fill there is capillary action between the individual lines of printed material at the base of the sponsons. This causes water to slowly seep into the model. As I plan on priming the boat, hydro dipping, clear coating then waxing these four layers should seal off the capillary gaps. A couple coats of flexible primer would probably do the trick - focus more primer on the flat surfaces that serve as the first layer of Boaty and McBoatface prints. If you plan on running your boat without these coatings I've read that brushing or submerging in melted candle wax (not too hot though - Paraffin starts melting at 37 deg C / 99 deg F) can seal a 3d print, if you are a motorcyclist you likely have a can of Maxima chain wax (best chain lube ever :) - this is essentially parrafin wax with some additives in a carrier fluid and can likely serve the same purpose without the messy melting (though I'd be concerned if any of the additional additives would leach into the water). Along the same thought process I'm thinking that carnauba car wax would likely work too though be less durable. Btw if you do use wax keep fire safety in mind as some FDM plastics are flammable and wax has now made it even more flamable. Another method that I've seen RC airplane makers use for waterproofing is to coat model in a very very thin layer of gorilla glue - it doesn't bubble up too much if the layer is thin enough. A waterproof wood glue like titebond might even work - I'm not sure how well it would adhere to FDM polymers. If anyone in the RC community has any suggestions they would be welcome - maybe when you post your make you can let us know how you waterproofed your model :). I'll post pictures of my own process soon.
BOM:
Motor: 2212 Though, with some work, you can now use an alternate motor with the custom motor plate template "Custom Motor Plate Template.stl" (Dimensions center to center between the 3 mm mounting holes are 49 mm X 23.41 mm. The top surface of the mounting plate (measured from the large flat area not the post) is 18.738 mm below the center-line of the propeller axis). Keep weight and cooling considerations in mind if using an alternate. If using the 2212 just download the original 2212 Motor Mount. (I don't have enough experience to say what KV level is ideal, I am leaning towards lower KV motors as they deliver the same torque at lower amps with higher KT values. We like KTs - get it...KTs?) https://www.aliexpress.com/item/32672300112.html
ESC: SimonK 30A 4S with BEC (you will need to seal or find an alternate water proof ESC) https://www.aliexpress.com/item/32308790386.html
Prop: 32mm with 100 mm shaft (note get the 10 cm one with 3.18 motor as the 2212 shaft is 3.175 mm - I initially tried to model an axial flow impeller but I found this purchased item to be far more sturdy. Advantages are it has built in high speed bearings and replacement props can be purchased from here as well. I also added provisions for a diy 3mm shaft using 623 bearings) https://www.aliexpress.com/item/32714017489.html https://www.aliexpress.com/item/32528668718.html
Servo: 9g servo (important you will want to waterproof or find an alternate waterproof servo) https://www.aliexpress.com/item/33005962141.html
Reinforcement: 6 mm OD 4 mm ID Carbon Fiber Rods https://www.aliexpress.com/item/32310771446.html
Power Source (btw if, like me, you are inexperienced with RC make sure to inform yourself about some of the precautions needed with lithium based batteries especially around charging and storage. Unlike your consumer electronics the LiPo cell is very much exposed in RC and special care must be taken. RC Review and FliteTest do some good youtube vids on the matter) :
Cat Grumpiness
3S LiPo power pack (I was able to find a 1300 mAh one that fits well 3S 1300 mAh 60C LiPo 75 X 34 X 24 mm - The maximum extents of a battery able fit in the front of the boat are 82 X 36 X 26 mm if removal is not needed)
18650 batteries are no longer being supported, battery compartments are left in but I've come to the conclusion that its just not a good idea..I originally thought it would be cheaper owing to relatively inexpensive cells and BMS modules but once you add a constant current power supply for charging, nickle strip welder, and discharge rate / weight / C.G considerations LiPo starts to make a lot more sense...never mind the potential effects of water on Li Ion cells...
Receiver and transmitter: Up to you (and your local regulations), I'm using a Flysky FS-i6X transmitter and FS-GR3E Waterproof receiver (note i6X will need to be in AFHDS mode to work with FS-GR3E) https://www.aliexpress.com/item/32785968777.html https://www.aliexpress.com/item/32892188833.html
M3 X 6 X 5.3 Embedded Nuts (old link no longer works - possible substitution M3 X D5 X L6) https://www.aliexpress.com/item/4000232858343.html
M3 Machine Screws (Button head and Flat head) https://www.aliexpress.com/item/32798146322.html or stainless https://www.aliexpress.com/item/32934186482.html
XT60 connectors, 3.5 mm bullet connectors, grease (marine), filament material compatible glue. The connectors are sold by the same storefront as much of the material above.
Sound system: Bongo Cats
Tentative Print Settings (Cura has a setting under Travel called combing mode which helps reduce stringing in the inaccessible interior). Personally I'm printing in PETG but ABS or ASA might be a good options too if you are setup for that with enclosure and ventilated space (due to easier gluing / reduced density - if using ABS or ASA I would advise against acetone smoothing as thin walls will likely deform). I excluded PLA as it is not as temperature / weather / UV resistant as the above materials and will swell / deteriorate in water unless waterproofed. I print at 30 mm/s or less but it might still print well at more default speeds of 60 mm/s. Thrust vector nozzle and 2212 cooling impeller will be printed in TPU for its reliable layer adhesion as both components will be subject to cyclic loading and high shear stress. STL files are already saved in as print orientation.
PETG/ABS/ASA Parts
Boaty (PETG/ABS/ASA): 0.4mm nozzle, 0.15mm layer height, 1 walls, 3 bottom layers, 3 top layers, 14% grid infill, supports on overhangs over 80% touching buildplate (apx 116 grams)
McBoatface (PETG/ABS/ASA): 0.4mm nozzle, 0.15mm layer height, 1 walls, 3 bottom layers, 3 top layers, 14 % grid infill, supports on overhangs over 80% touching buildplate, brims are helpful for ensuring support adhesion (apx 218 grams)
Cover: TBD (PETG/ABS/ASA) 0.4mm nozzle, 0.15mm layer height, 1 walls, 3 bottom layers, 3 top layers, 14% grid infill, supports on overhangs over 60% touching buildplate (apx 12 grams)
2212 Motor Mount (PETG/ABS/ASA): 0.4mm nozzle, 0.15mm layer height, 5 walls, 3 bottom layers, 3 top layers, 25% grid infill, supports on overhangs over 80% touching buildplate, brims are helpful for preventing warping (apx 30 grams)
Ride Plate: (PETG/ABS/ASA) 0.4mm nozzle, 0.15mm layer height, 5 walls, 3 bottom layers, 3 top layers, 25% grid infill, supports on overhangs over 80% touching buildplate (apx 6 grams)
Servo Hatch: (PETG/ABS/ASA) 0.4mm nozzle, 0.15mm layer height, 4 walls, 3 bottom layers, 3 top layers, 100% infill, supports on overhangs over 80% touching buildplate, Brim (apx 2 grams)
TPU parts
Thrust Vector Nozzle: (TPU) 0.4mm nozzle, 0.15mm layer height, 3 walls, 3 bottom layers, 3 top layers, 25% cubic subdivision infill, supports on overhangs over 80% touching buildplate (apx 15 grams)
Stator Bowl: (TPU) 0.4mm nozzle, 0.15mm layer height, 3 walls, 3 bottom layers, 3 top layers, 25% cubic subdivision infill, supports on overhangs over 80% touching buildplate (apx 24 grams)
Cooling Impeller: (TPU) 0.4mm nozzle, 0.15mm layer height, 2 walls, 4 bottom layers, 4 top layers, 100% concentric infill, (apx 2 grams). Note this part narrows to a single wall of 0.4mm TPU - slowing down print speed drastically (15 mm/s) is likely needed for successful print
Motor (50 grams), LiPo (129 grams) (18650s are out), ESC (28 grams), servo (9 grams), and receiver (6.5 grams)
A note for early downloaders: I tend to iterate and reiterate a design multiple times before I'm happy with it. Designs subject to change...frequently...
N7 Cat Says: "Dis my bigges and shiniest objec yet, 2020 u cray cray, I jus gonna yeet away from u in mah boat wif mah other kitteh fiends"
Updated: 9/28/2020, Updated files Boaty and Cover, added provisions for gluing a 5mm X 2mm magnet on the cover and boat for magnetic latching
Updated: 9/29/2020, fixed a problem with McBoatnose missing modeled tube for carbon fiber reinforcement.
Updated: 10/2/2020, added a custom motor plate "McBoatface Custom Motor Plate.stl" for anyone wanting to use a motor other than the 2212. Intent is that you will be able to model your own motor housing (and share with others along with recommendations for ESC and battery :) for mounting onto the flat plate. 3 mm dia screws will secure the motor mount to the two sections of the boat, as the mount will be subject to vibration fastening hardware (embedded nuts or lock nuts) is recommended in your design. Like the original requires brims and supports.
Updated 10/4/2020, added battery holder compartments along the length of the hull for an integrated 3S 2P 18650 setup. I'm planing on spot welding the batteries together with pure nickle strips and wiring to BMS. Note there are two battery caps (non symmetric). Added a baffle near the motor cooling impeller to improve airflow and cooling. Additionally minor improvements to printability around the servo mount and filleting of vortex outlet. For custom motor users new battery holders and air baffle might interfere with especially big motors but you can model / clip them out if needed.
Updated 10/6/2020, added built in support for servo hatch opening, improved joints between the three boat hull sections by adding grooves and other features for the expanding polyurethane glue to latch onto. Fixed a printability issue with the fillet that supports the propeller shaft. Started first print of the boat section, may update if issues crop up after print finishes.
Updated 10/7/2020, added a channel in the battery compartment to allow for wire to be routed through.
Updated 10/8/2020, post printing improvements, increased diameter of battery compartment, prop shaft and carbon fiber shaft openings. Improved servo hatch support structure to make it easier to remove.
Update 10/9/2020, Estimated static resting position of the boat in water and calculated rough target mass for finished boat. After a print failure of the protective grid on the intake as well as impact durability test failures I have replaced with a filament heat stake method as shown below in post processing pics.
Insert 1.75 mm filaments into the slots and use a low temp soldering iron to melt the ends into the inlet - you could also use servo wire and glue in place...unless you like grinding baby fish into a pulp...u monster
Updated 10/11/2020, with 18650s looking like less and less of a good idea and mass being more of a concern I trimmed the battery compartments down to two 0.4 mm walls. This reduces mass and print time dramatically.
Update 10/11/2020, realized I derped and forgot to add an access port for servo wiring. I've created an access port on the battery compartment closest to the servo wire (port/left side). As there were some unbridgeable overhangs I made some built in supports that need to be pried or clipped out before use.
Update 10/12/2020, created an alternate path for servo wire on the top of the baffle in case I decide to house all electronics in the cover. After fighting with carbon fiber tube on second print increased the diameter of the carbon tube channel and started printing again :P Ever had a carbon fiber sliver? I haven't nor do I ever want to...make sure to wrap the end of the tube that you are handling in masking tape or something to protect your hands
Updated 10/14/2020, minor improvements to Boaty and McBoatnose to reduce support generation. Trying some new tricks to strengthen servo mount and embedded nut support by creating additional walls in those areas. Improved airflow on McBoatnose 2212. Updated the stator bowl as supports were not properly generating - something to do with angle of one of the pieces aligning with support autogenation void
Updated 10/15/2020, McBoatface 2212 motor mount was a bit of a tight fit, adjusted motor mount. Adjusted joints between sections
Updated 10/16/2020, added receiver tray and antenna port to cover
Update 10/18/2020, added mounting points for turn fin in case they are needed - I couldn't find any info on whether one would be needed for a pump jet nor dimensions for standard mounting points. Converted the fixed ride plate to a variable trim ride plate using 1.5 mm servo wire as the adjustable retention mechanism. Backup retention provided by an embedded nut and M3 X 10 screw + spring. Joint held by filament joint
Updated 10/20/2020, some weird artifacts were cropping up in cooling impeller during slicing, increased to high resolution stl and fixed wall width. Encountered a problem with McBoatnose tips coming off due to single walls and how narrow it becomes. Blunted the tips. Also had to physically clip some of the joints between front and mid section in order to get it to fit, adjusted the model so this is not required. Carbon Fiber tubes now provide most of the support between the front and mid section. Created McBIGface for those of you with Z axis build volume above 280 mm so you can print mid and front sections as one piece #jealouscat (note that this will result in a weaker motor mount as you will still need to balance weight considerations with strength requirements - play around with slicer settings starting from McBoatnose as a baseline)
Updated 10/21/2020, increased prop clearance in stator bowl
Updated 10/22/2020, Major overhaul...N7 cat shredded all the toilet paper...McBoatface and McBoatnose now one part, motor mount now modular for both 2212 and custom motors, added a custom motor mount template, increased sponson size 25%, other minor improvements
Update 10/24/2020, tried to reduce weight of McBoatface by hollowing out the sponsons, turns out a solid object with grid infill doesn't contribute much to weight...who knew...saved 5 grams!
Update 10/26/2020, realized that the cover / McBoatface interface would allow water to seep in at the front seam, updated these two parts to improve water shedding in this area. Added a part called Compatibility Shim For Pre Oct 22 Update Boaty Prints.stl which will allow any prints of Boaty made prior to 10/22 update to be used with new McBoatface
Update 10/27/2020, major iteration work completed - only minor changes from this point on - latest files re-uploaded to sync with my local files. Post processing instructions will be completed once prints are completed
Update 10/28/2020, vortex was breaking during print, strengthened the part with additional walls
Update 11/4/2020, updated servo hatch (missing cutout for gear)
Update 11/5/2020, work in progress status lifted - no major issues encountered during assembly
Updated 11/6/2020, after dropping my completed boat noticed one of the sponsons cracked ;.; strengthened the sponsons with option to add 200 mm carbon fiber tube reinforcement (adds ~35 grams to total weight inc carbon tubes or ~ 15 grams without carbon reinforcement). Thanks to a helpful tip from the community I have added a 5 degree pitch up to the thrust vector nozzle - if your boat has a nose down attitude and the ride plate adjustment is not enough this should hopefully correct that. There is a moment force applied by the thrust which pushes the nose down, this minor tweak will hopefully apply a slight corrective force which allows the boat to get on stable plane. Added a ride plate servo wire retention slot to stator bowl. Increased McBoatface carbon tube clearance. Added a 10 deg pitch nozzle in case 5 deg is not enough, as I'm still waiting on batteries to arrive I haven't had a chance to perform test to determine which will be best. Performed submersion test and posted results near the top of this summary
Update 11/8/2020, moved the Boaty magnet catch to the top surface instead of underside to improve ease of assembly. Closed the opening in the baffle since servo wire was long enough to not need it. Moved the cover magnet closer to the Boat magnet to improve latching strength. Improved McBoatface by filleting the sponson to wing interface and creating water rejection channels near the vortex exits.
Update 11/15/2020, added a version of cover with provisions for 3mm LED navigation lights
Update 11/18/2020, first functional test of the waterjet, I found that even with TPU gasket air and water would spray out thus sealing the stator bowl to boat body with silicone or glue is necessary. I found an issue with air locking - I don't fully understand the cause but experimentally determined a way to resolve this via a pending modification to the thrust vector nozzle. Update uploaded (Thrust Vector Nozzle Variable Pitch) but untested - I'll hopefully get a chance to print and test by tmw. Testing confirms the air lock issue is resolved with this new nozzle - there is some loss of efficiency. I don't really know why this fixes the air lock but I suspect the stator bowl fins were not redirecting enough of the rotational energy generated by the prop resulting in an area of low pressure which would draw air in from behind the outlet...without high speed cameras or CFD I can't really say. N7 Cat says "wut he trying 2 say iz I putz mah paw ober da nozzle and dat fixes it"
11/21/2020 did some more study on propulsor units and updated the pitch and number of stator vanes - 5 vane stator uploaded - will test later and delete original if testing displays improvement. Test showed marked improvement in both trust and elimination of air lock using the 5 vane stator - original deleted. For anyone else designing or trouble shooting other pump jets on thingiverse the number of stator vanes needs to be a prime number and different than the number of prop blades otherwise a standing wave can develop. At some point in the future I might experiment with a properly designed axial flow prop and stator - salt sintering might be able to create a strong enough part for use as a prop.
11/25/2020 reverted thrust vector nozzle to neutral pitch
Similar models
thingiverse
free
Pump Jet (32mm Prop) by N7_Cat
...ntering might be able to create a strong enough part for use as a prop.
11/25/2020 reverted thrust vector nozzle to neutral pitch
thingiverse
free
S800 Reptile addons by slibbinas
...nas
thingiverse
printed in pla or ep-cf (nylon carbon)
0.15mm layer
0.4mm nozzle
printer creality 3d
camera_cover - for runcam3
thingiverse
free
RC swamp boat
...ilament
printed on a prusa mk2
you'll need 4mm shafts and collars for the rudder hardware.
bad pics of some details attached.
thingiverse
free
Nozzle Holder by MaczkanicsG
....4mm nozzle, 0.15mm layer height
3x 0.2mm nozzle
3x 0.3mm nozzle
2x3 0.4mm nozzle
3x 0.5mm nozzle
3x 0.6mm nozzle
3x 0.8mm nozzle
thingiverse
free
PTFE Tube fitting
...tube fitting
thingiverse
printing without supports with a layer of 0.1mm line width 0.4mm. i used a 0.4 mm nozzle. 100% filling.
cg_trader
$3
3d file to print a Key that hold your keys | 3D
...trader
this is a file to 3d print. it can be printed without supports. i printed it with pla, 0.15mm resolution, 0.4mm nozzle.
thingiverse
free
Simple mini planter with drainage - Pentagon version by jphphotography
... plan on updating my other design soon.
designed to print using a 0.4mm nozzle with 0.4mm layer height and 3 top/bottom layers.
thingiverse
free
Canoe Polo Figures by lhammer
...n 50% scale with support.
the paddels break off easily.
i printed them with a 0.4mm nozzle and 0.2 mm layer hight on an anet a8.
thingiverse
free
Fabrikator AutoBed Leveling case and support by CarlDesign
... the head, using the 2 screw on the left.
i hope it will be also useful !
i print this with 0.2mm layer and 0.4mm for the nozzle.
thingiverse
free
FreeStyle Libre dust protector by yschaeff
...zzle
0.15mm layer hight
no support
no brim
petg
if you have a smaller nozzle you might want to increase the number of perimeters.
N7
3ddd
$1
Стол N7 от Casamania
...стол n7 от casamania
3ddd
casamania
футуристичный стол n7 от casamania
evermotion
$8
CASAMANIA N7 AM72
...nia design with all textures, shaders and materials. it is ready to use, just put it into your scene.. evermotion 3d models shop.
3d_export
$12
Clothes n7
...tures are in png format and they are available in these dimensions:<br>dimensions of the 3d model: 0.402m x 0.324m x 0.912m
turbosquid
$10
Bamboo decor wall n7
...oyalty free 3d model bamboo decor wall n7 for download as max on turbosquid: 3d models for games, architecture, videos. (1476998)
turbosquid
$12
Pebble low n7 form rentangle
...ree 3d model pebble low n7 form rentangle for download as max on turbosquid: 3d models for games, architecture, videos. (1523401)
turbosquid
$12
Pebble river low n7
...royalty free 3d model pebble river low n7 for download as max on turbosquid: 3d models for games, architecture, videos. (1523351)
turbosquid
$12
Panel stone brick n7
...oyalty free 3d model panel stone brick n7 for download as max on turbosquid: 3d models for games, architecture, videos. (1478938)
turbosquid
$12
Panel stone decorative n7
...y free 3d model panel stone decorative n7 for download as max on turbosquid: 3d models for games, architecture, videos. (1482500)
turbosquid
$60
Spaceship N7-3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$50
Spaceship N7-2
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
喷射泵
thingiverse
free
Fletching (FOB) Archery by lidaiyang
...e stable in theory.
because the fob-3 and - 4 are too close to the shaft, we have to use special tools, which is very convenient.
thingiverse
free
ender6 BLtouch by chimaer
...thingiverse
ender6 bltouch
this is an external bracket
这是创想三维ender6 机器的 外挂bltouch 支架,其实ender6 本身就就能直接安装bltouch 拆喷头开风扇 你会看到两个螺丝孔
thingiverse
free
炸寒單_玄武堂 by NTTUEIDM
...單爺接受炮轟的儀式展演,火光四射場面深具魅力而撼動人心,在當代宗教活動中展現出其獨特的慶典美學,是呈現臺東地方特色的重要文化資產。
資料來源:https://www.taiwangods.com/html/landscape/1_0011.aspx?i=92
thingiverse
free
炸寒單_遶境活動 by NTTUEIDM
...單爺接受炮轟的儀式展演,火光四射場面深具魅力而撼動人心,在當代宗教活動中展現出其獨特的慶典美學,是呈現臺東地方特色的重要文化資產。
資料來源:https://www.taiwangods.com/html/landscape/1_0011.aspx?i=92
thingiverse
free
秦始皇兵馬俑跪射俑 by hkepel3d
...秦始皇兵馬俑跪射俑 by hkepel3d
thingiverse
秦始皇兵馬俑跪射俑
thingiverse
free
Sakura Mold for Hot glue Injection by Nature3D
...み温度140℃以上を推奨)
今回はこちらを使いました http://nature3d.net/filament/lfy3m.html
m3ネジ、ナット
水性ニス(アクリル系。表面平滑化および離型剤吸い込み止めとして使用)
シリコンオイル(離型剤として使用)
thingiverse
free
Identity V - NURSE WEAPON - syringe第五人格护士注射器 by 195CN
...length 25mm
diameter 4, length 25mm
length can be cut according to need, diameter can not be changed, otherwise it can not match.
thingiverse
free
Magatama Mold for Hot glue Injection by Nature3D
...要なもの
グルーガン(160℃以下のもの)
グルースティック(eva系)
耐熱plaフィラメント(荷重たわみ温度140℃以上を推奨)
今回はこちらを使いました http://nature3d.net/filament/lfy3m.html
m3ネジ、ナット
thingiverse
free
Clover Mold for Hot glue Injection by Nature3D
...要なもの
グルーガン(160℃以下のもの)
グルースティック(eva系)
耐熱plaフィラメント(荷重たわみ温度140℃以上を推奨)
今回はこちらを使いました http://nature3d.net/filament/lfy3m.html
m3ネジ、ナット
遥控船
thingiverse
free
MiniPlan_TinyPlan_v4.0 by OK1289
...inyplan_v4.0 by ok1289
thingiverse
miniplan_tinyplan_v4.0 這是一塊電子控制板
miniplan_tinyplan_v4.0 this is an electronic control board
thingiverse
free
綠島燈塔 by NTTUEIDM
...印象派的絕佳畫作。 到了夜晚,它便搖身一變成為「航海人的守護者」,是漁船、飛機的重要指標,亦為太平洋上深具歷史意義的一盞明燈。
說明資料來源引用:https://tour.taitung.gov.tw/zh-tw/attraction/details/377
thingiverse
free
拼板舟 by NTTUEIDM
...之一;在飛魚季的招魚祭時,大船成為部落中家族合作的表徵
說明資料來源引用:https://travel.lanyu.info/tao-culture/%e9%81%94%e6%82%9f%e7%9a%84%e6%8b%bc%e6%9d%bf%e8%88%9f
thingiverse
free
taste of Niagara Falls tour boat by scrap_and_build_lb
...taste of niagara falls tour boat by scrap_and_build_lb
thingiverse
ship objet
double decker
ナイアガラの滝
観光遊覧船
thingiverse
free
日本遣隋使、遣唐使船 by hkepel3d
...日本遣隋使、遣唐使船 by hkepel3d
thingiverse
日本遣隋使、遣唐使船
thingiverse
free
drawbot by MG-dream-technology
...续会更新,可以关注arduino中文论坛直播贴
简介:
桌面级scara机械臂,运动机构为两个42步进电机和一个9g舵机,控制板为mega 2560 和ramps 1.4,其他部件主要为3d打印件,工作范围为a4纸,使用国标g代码,目前可以实现写字画画功能。
thingiverse
free
藍芽喇叭筆筒 by cuknsfgzj612
...結合再一起,桌上少了零散的文具,就會非常乾淨方便,喇叭與筆筒外殼都是使用coreldraw x6這個程式來設計自己喜歡的圖片與外殼,再用雷射切割機切出來,裡面的電路也非常簡單,兩個喇叭和一個電池盒街上藍芽控制板,另外筆筒的部分,就直接用三秒膠黏上去就完成了。
thingiverse
free
L298N直流馬達控制板(DC motor control board) by OK1289
...l298n直流馬達控制板(dc motor control board) by ok1289
thingiverse
這是直流馬達控制板
this is the dc motor control board
thingiverse
free
移動藍芽喇叭 by OK1289
...charge(bk4202)(3.7v轉5v充放電模組)1
mini usb female(mini usb母頭)1
rocker switch(2p船型開關)1
3.7v 8000mah lithium battery(3.7v 8000mah 鋰包)1
Pump
3d_export
$8
S revit 1 3D Model
...s revit 1 3d model 3dexport boot women girl pump shoe leater heel tassel brown baked white high detail...
3d_export
$8
Mesh boot 3non rigged 3D Model
...boot 3non rigged 3d model 3dexport boot women girl pump shoe leater heel tassel brown baked white high detail...
3d_ocean
$25
GardenHouse2
...garden house home house ivy low poly old water pump place single house small apartment spathiphyllum low poly garden...
3d_ocean
$19
Oil Pump (Pumpjack)
...od choice for arhitecture vizualisations, video games and etc. possible in: c4d r11, c4d r15, max 2010, dae 1.4, fbx 6, 3ds, obj.
3d_export
$20
Gas Pump Gilmore 3D Model
... antique pipe meter fuel 3d
gas pump gilmore 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl joshim 106934 3dexport
3d_export
$99
Remington Model 870 3D Model
...model 3dexport remington model 870 combat shotgun shot gun pump semi automatic us american weapon army remington model 870...
3d_export
$20
Gas Pump Musgo 3D Model
... gulf antique pipe meter fuel
gas pump musgo 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl joshim 106937 3dexport
3ddd
$1
Декоративный набор Decor
..., фоторамка , рама , prisma , туфли , pump , коробка , стена , молдинг декоративный...
3ddd
$1
Pottery Barn
...barn http://www.potterybarn.com/products/holden-glass-metal-bath-accessories/?cm_src=autocatrel toothbrush holder: 3.5" diameter, 4.5" high soap pump 3.5" diameter, 6.75" high small canister: 4.5" diameter, 4.5"...
archive3d
free
Pump 3D Model
... model
archive3d
pump water pump
pump 1 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Rc
3ddd
$1
Roberto Cavalli RC 13003b
...roberto cavalli rc 13003b
3ddd
roberto cavalli
обои roberto cavalli и industrie emiliana parati spa, rc 13003b
3d_ocean
$25
RC F1
...rc f1
3docean
auto car control f1 formula race rc remote speed
remote control f1 car
3d_ocean
$19
Braid 4 RC wheel + tyre
...heel (tire + rim + brake disc + caliper) has 30.700 polygons (not smoothed). i didn’t applied (collapsed) a smooth modifier on...
3d_ocean
$89
Lexus RC 2014
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
3ddd
$1
LG G2 smartphone
...3g (hspa+42mbps / hspa+21mbps) lte (svlte, csfb, ca, volte, rc, mimo) dimensions ** 138.5 (l) x 70.9 (w) x...
3ddd
$1
Робот-пылесос "Karcher RC 3000"
... робот , пылесос
робот-пылесос "karcher rc 3000"
3ddd
$1
Kuppersberg RC 699 ANT BRONZE
...kuppersberg rc 699 ant bronze
3ddd
kuppersberg , духовой шкаф
электрический духовой шкаф
3ddd
$1
Klipsch
...klipsch rf-83 floorstanding speaker, rt-12d subwoofer, rs-62 surround speaker, rc64 center speaker модели детальные, по размерам, с текстурами. 148370...
cg_studio
$99
RC buggy model3d model
...o
.3ds .c4d .fbx .lwo .max .obj .xsi - rc buggy model 3d model, royalty free license available, instant download after purchase.
3ddd
$1
BOSS RC-2 Loop Station
...rc-2 loop station
3ddd
гитарный эффект boss rc-2
педаль позволяет записать аудио, наложить петли друг на друга, закольцевать их.
Jet
3d_export
$85
JAS 39 Gripen Jet 3D Model
...ipen jet 3d model
3dexport
aircraft airplane fighter military attack jet
jas 39 gripen jet 3d model vanishingpoint 72995 3dexport
3d_export
$65
News Helicopter 3D Model
...news helicopter 3d model 3dexport aircraft airplane commercial jet airliner civilian flight vehicle transportation helicopter news r44 news...
3d_export
$40
Cessna citation cj4 3D Model
...cessna citation cj4 3d model 3dexport airplane jet aircraft bussines plane private civilian wings cessna citation cj4...
3d_export
$95
Falcon3D A319 United Airlines 2 3D Model
...airplane aircraft airliner plane transport commercial passenger modern twin jet civil civilian a320 a321 a318 a319 airbus falcon3d a319...
3d_export
$95
Falcon3D A340 600 Pacific Charters 3D Model
...plane transport commercial passenger modern twin jet civil civilian jetiner a340 a-340 a-340-600 a340-600 airbus falcon3d a340 600 pacific...
3d_export
$95
Falcon3D MD 80 Hawaiian 3D Model
...freight cargo corporate mcdonnell douglas us plane planes jet jetiner md-80 falcon3d md 80 hawaiian 3d model falcon3d 73148...
3d_export
$65
Aircraft 737 3D Model
...aircraft 737 3d model 3dexport aircraft airplane commercial jet airliner civilian flight vehicle transportation aircraft 737 3d model...
3d_export
$95
Falcon3D MD 80 Fast Cargo 3D Model
...freight cargo corporate mcdonnell douglas us plane planes jet jetiner md-80 falcon3d md 80 fast cargo 3d model falcon3d...
3d_export
$50
Bell 407 Jetranger 3D Model
...e commercial jet airliner civilian flight vehicle transportation helicopter
bell 407 jetranger 3d model digimation 73228 3dexport
3d_export
$85
Tempest 3D Model
...tempest 3d model 3dexport aircraft airplane fighter military attack jet british england raf tempest 3d model vanishingpoint 73000...
Cat
3d_export
$64
Lion Head Door Knocker 3D Model
...bronze gate handle brass ornate antique stone sculpture lock cat big statue game ready low lion head door knocker...
3d_export
$40
Cat Skull ZBrush Sculpture 3D Model
...ure 3d model
3dexport
cat feline skull bones kitty cranium pet
cat skull zbrush sculpture 3d model saschasnowstorm 73801 3dexport
3d_export
$5
Cats Statuette Very Detailed 3D Model
...rcelain statue interior animation design 2013 high poly character
cats statuette very detailed 3d model alienworld 68709 3dexport
3ddd
$1
Аллегро Классика Дубай
...аллегро классика дубай 3ddd аллегро-классика страничка с описанием:http://www.argomeb.ru/catitem953_98.htm ...
3ddd
$1
WILLIE CHANDELIER
...willie chandelier 3ddd gramercy home люстра из ракушекhttp://gramercy-home.com/catlight/chandeliers/chandeliers/1673 ...
3ddd
$1
Mikado
...mikado 3ddd mikado please check the site for product information:http://www.tropicdane.com/?frame=furniture_pro_detail&cat=206&cat2;=306&id;=551 thank...
3d_ocean
$19
Brown Kitten
...brown kitten 3docean animal baby beautiful cartoon cat cats child children comics cute domestic fantasy feline game gato...
3d_ocean
$19
White Brown Kitten
...white brown kitten 3docean animal baby beautiful cartoon cat cats child children comics cute domestic fantasy feline game gato...
3d_export
$19
Catwoman Lego 3D Model
...erson cat woman catwoman
catwoman lego 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl digitallab3d 104326 3dexport
3d_export
$15
Speedy Gonzales 3D Model
...speedy gonzales looney toones cartoon mouse daffy duck silvester cat low poly speedy gonzales 3d model download .c4d .max...
Boat
3d_ocean
$9
Old Boat
...docean
3d boat creek fisher old river rope row water wood
lowpoly old fisherboat model, with textures for pbr shaders (2048*2048)
3d_ocean
$12
Toy boats
... ship toy water
scene contains 3 models of toy boats. the file includes materials. rendered in 3ds max 2012 /v-ray 2.4/ p /9 856/
3d_export
$59
Sailboat 3D Model
...real game ready watercraft cruising
sailboat 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl djkorg 110692 3dexport
3d_export
$180
Sailboats 3D Model
...nture game ready mid poly hms royal
sailboats 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl sobul 108780 3dexport
3d_export
$59
Schooner 3D Model
...schooner 3d model 3dexport sea sail boat pirates linear heavy manowar wooden medieval port adventure game...
cg_studio
$199
Oil Tanker Ship Evergreen State3d model
...state3d model cgstudio class transport ship tanker shell bellamya boat supertanker hantiers de l'atlantique saint-nazaire batillus oil transportation ulcc...
cg_studio
$129
USS Zumwalt DDG-10003d model
...army military modern ship patrol uss battle stealth recon boat sea zumwalt ddg-1000 ddg1000 invisible .max .lwo .fbx .c4d...
3d_export
$80
Sailing yacht model 3D Model
...sailing yacht model 3d model 3dexport yacht ship vessel boat sails sailing yacht model 3d model download .c4d .max...
3ddd
$1
Декоративная панель Maori 120x120
...незаурядных all from boats. артикул panel-afb-maori бренд all from boat ширина 120 см глубина 3 см высота 120 см...
cg_studio
$20
Footbridge Low Poly3d model
...footbridge wood old pillar port lake forest river derelict boat edge pier molo water dock marina shore ship sea...