Thingiverse
#MicroLongRange OpenHD iNav Sub250g by user13name13
by Thingiverse
Last crawled date: 3 years, 1 month ago
#MicroLongRange OpenHD iNav Sub250g
The frame design borrows, remixes, and is inspired by the original #MLR from Dave_C_FPV.
https://www.thingiverse.com/thing:4054381
Flight controller is running iNav. To get Telemetry to OpenHD only a free serial port is connected to the RPi and the MavLink telemetry output is selected in port in iNav configurator.
https://github.com/iNavFlight/inav/wiki
OpenHD is running on an RPi-ZeroW on the Multirotor and a RPi4B on the groundstation.
There are many options for the Digital video link VRX/VTX using WIFI radios in raw broadcast mode. This provides a high speed low latency digital video link. Similar to the DJI FPV system.
The OpenHD Wiki and instructions are found here:
https://github.com/OpenHD/Open.HD/wikihttps://openhd.gitbook.io/open-hd/
Digital System
RaspberryPi-Zero Linux SBC
Asus AC-56 Digital Transmitter
Waveshare 5MP Digital Camera
Multirotor
Matek F722SE-Mini
Matek M8Q-5883L GPS-Compass
Diatone F30 Esc
TBS Crossfire
Mamba 1404/3750Kv
3A BEC
All of the TPU parts are re-designed to best fit the OpenHD system and iNav. These should be interchangeable with most parts from the #MLR builds as most major dimensions are kept the same.
The body of the frame was redesigned to accommodate the RPi underneath the quad, the flight controller/ESC was split flat, leaving a large long open space for mounting the Wifi cards. If you are using a short card you can stack the ESC/FC normally. If you are using any of the long dongles, like the ASUS AC-56 the stacks need to be split.
The arms come from the original #MLR build, I think the Flywoo Explorer LR arms should also fit however I don't have a set to confirm.
Digital 5.8Ghz Wifi Broadcast Options
AR9271 150M [very good results with this card, also $11USD]
ASUS AC-56 [also very good, more $]
WISE TIGER Wifi Adapter Ac 600Mbps [tiny, available on amazon]
Ground Station Card
Alfa Long-Range Dual-Band AC1200 Wireless USB 3.0
Check the OpenHD wiki for more options and power ratings.
Air Units
RPi-ZeroW, Tiger Wifi, Zero Cam - weight 10g - $30 USD
RPi-ZeroW, ASUS AC-56, Waveshare M12 Lens Digital 5MP Camera - weight 29g - $60USD
RPi-ZeroW, AR9271, Waveshare 12MP - weight 26g - $35USD
Building
Recommended to print the design on paper or 3D printer to check dimensions of the hardware you are using as there are many different cameras, WIFI adapters, flight controllers, ESC combos.
Updates
March 23rd
CARBON_1.5mm_LowerDeck_M2
CARBON_1.5mm_UpperDeck_M2
The standard frame is for rear M3 mounting of the Matek F722SE Mini which uses M3 holes in the FC. Most FC 20x20 boards are M2. New Decks are sized for Front/Rear 20x20xM2.
The frame design borrows, remixes, and is inspired by the original #MLR from Dave_C_FPV.
https://www.thingiverse.com/thing:4054381
Flight controller is running iNav. To get Telemetry to OpenHD only a free serial port is connected to the RPi and the MavLink telemetry output is selected in port in iNav configurator.
https://github.com/iNavFlight/inav/wiki
OpenHD is running on an RPi-ZeroW on the Multirotor and a RPi4B on the groundstation.
There are many options for the Digital video link VRX/VTX using WIFI radios in raw broadcast mode. This provides a high speed low latency digital video link. Similar to the DJI FPV system.
The OpenHD Wiki and instructions are found here:
https://github.com/OpenHD/Open.HD/wikihttps://openhd.gitbook.io/open-hd/
Digital System
RaspberryPi-Zero Linux SBC
Asus AC-56 Digital Transmitter
Waveshare 5MP Digital Camera
Multirotor
Matek F722SE-Mini
Matek M8Q-5883L GPS-Compass
Diatone F30 Esc
TBS Crossfire
Mamba 1404/3750Kv
3A BEC
All of the TPU parts are re-designed to best fit the OpenHD system and iNav. These should be interchangeable with most parts from the #MLR builds as most major dimensions are kept the same.
The body of the frame was redesigned to accommodate the RPi underneath the quad, the flight controller/ESC was split flat, leaving a large long open space for mounting the Wifi cards. If you are using a short card you can stack the ESC/FC normally. If you are using any of the long dongles, like the ASUS AC-56 the stacks need to be split.
The arms come from the original #MLR build, I think the Flywoo Explorer LR arms should also fit however I don't have a set to confirm.
Digital 5.8Ghz Wifi Broadcast Options
AR9271 150M [very good results with this card, also $11USD]
ASUS AC-56 [also very good, more $]
WISE TIGER Wifi Adapter Ac 600Mbps [tiny, available on amazon]
Ground Station Card
Alfa Long-Range Dual-Band AC1200 Wireless USB 3.0
Check the OpenHD wiki for more options and power ratings.
Air Units
RPi-ZeroW, Tiger Wifi, Zero Cam - weight 10g - $30 USD
RPi-ZeroW, ASUS AC-56, Waveshare M12 Lens Digital 5MP Camera - weight 29g - $60USD
RPi-ZeroW, AR9271, Waveshare 12MP - weight 26g - $35USD
Building
Recommended to print the design on paper or 3D printer to check dimensions of the hardware you are using as there are many different cameras, WIFI adapters, flight controllers, ESC combos.
Updates
March 23rd
CARBON_1.5mm_LowerDeck_M2
CARBON_1.5mm_UpperDeck_M2
The standard frame is for rear M3 mounting of the Matek F722SE Mini which uses M3 holes in the FC. Most FC 20x20 boards are M2. New Decks are sized for Front/Rear 20x20xM2.
Similar models
thingiverse
free
Project #MicroLongRange OpenHD Edition by SLOWY
...ews, the longest you need is 16mm
the parts are designed to fit both:
the flywoo explorer frame and the original #microlongrange.
grabcad
free
LD 4inch 250g quadcopter
...penhd/open.hd
files are here for sharing. if someone want to use for commercial purpose, happy to do as long as i get mentioned.
thingiverse
free
Raspberry Pi Zero camera case for OpenHD or EZ-WifiBroadcast devices
...ase for openhd or ez-wifibroadcast devices
thingiverse
just simple case for rpi zero, sony imx219 sensor and ar9271hp wifi card.
thingiverse
free
24x24 FC mount for Matek F411 Wing by cmenard
...enard
thingiverse
this mount is intended to glue into your aircraft and allow mounting of the matek f411 wing flight controller.
thingiverse
free
LucyLongRange 6in 7in Digital/Analog iNAV (#minilongrange) by user13name13
...mlr5, each part was redesigned for this larger scale. similar remixes and designs exist, however were always missing something,...
thingiverse
free
RDQ Mach 1 Stack Mounts BF FC & 4in1 ESC by Daubut
...ottom of flight controller board. do not allow mounting screws to touch flight controller.
print in tpu infill 10% with supports.
cg_trader
$3
FPV drone ESC and FC Protection | 3D
... and esc safe from dirt, water, grime, grass and whatever.
printable shell for flight controller and electronic speed controller.
thingiverse
free
Long flight time 270mm quadcopter by antonpo
...ini with inav
camera: 600tvl 1/4 1.8mm cmos fpv 170
vtx: 200mw
osd: it is planned
gps: ublox
battery: li-ion 3s 2900ma (10a cont)
thingiverse
free
Nano Talon ESC and FC plates by synya
...nano talon esc and fc plates by synya
thingiverse
simple plates to mount matek f405 wing and esc in a bottom of nano talon
thingiverse
free
RPi Camera 5MP v1.3
...rpi camera 5mp v1.3
thingiverse
rpi camera 5mp v1.3
Openhd
3ddd
$1
Медиаплеер
...медиаплеер 3ddd медиаплеер , плеер медиаплеер openhd media box. размеры 190х135х25 мм. имеются все текстуры и...
thingiverse
free
OpenHD Fatshark module by datagr
...ts fatshark hdo (or any similar shaped goggles) into an openhd ground station.
i used velcro to secure the module on the goggles.
thingiverse
free
ZOHD Drift OpenHD Arducam mini HQ cam holder by SLOWY
...use it with the arducam hq imx477 mini cam but it can hold any cam with a similar form factor. 0 and 10 degree version available.
thingiverse
free
Project #MicroLongRange OpenHD Edition by SLOWY
...ews, the longest you need is 16mm
the parts are designed to fit both:
the flywoo explorer frame and the original #microlongrange.
thingiverse
free
S800 OpenHD Nose by MacDaddyFPV
...ill so that the overall weight of the nose, camera block and camera is approx 150g to enable a good cg with a 3s 2200mah battery.
thingiverse
free
Raspberry Pi Zero camera case for OpenHD or EZ-WifiBroadcast devices
...ase for openhd or ez-wifibroadcast devices
thingiverse
just simple case for rpi zero, sony imx219 sensor and ar9271hp wifi card.
thingiverse
free
ExpressLRS Camera Control OpenHD upgraded mount by datagr
...e to have video on the raspberry pi ground station.https://openhd.gitbook.io/open-hd/
https://www.youtube.com/watch?v=fiuq0uvmbdw
3d_sky
free
Media Player
...media player 3dsky player mediaplayer openhd media box. dimensions 190h135h25 mm. there are all the...
thingiverse
free
Open HD mini Pi4 GS 5.8 Ghz by SLOWY
...by slowy thingiverse this is a case for a openhd mini ground station. raspberry pi 4 alfa awus036ach 5v/5a...
Microlongrange
thingiverse
free
Holder BN-180 for #MicroLongRange by ZaJa
...holder bn-180 for #microlongrange by zaja
thingiverse
my holder bn-180 for #microlongrange
thingiverse
free
MicroLongRange Pritable by lucianobf
...microlongrange pritable by lucianobf
thingiverse
printable version of https://www.thingiverse.com/thing:4054381
thingiverse
free
MicroLongRange 2021 Parts by ZiegeOne
...s nano
dji vista
buzzer jhe42b_s finder
https://www.youtube.com/watch?v=vokiqqdb_54https://www.youtube.com/watch?v=qt3f8-y3exq
thingiverse
free
BN220 Mount for Dave C Microlongranger
...bn220 mount for dave c microlongranger
thingiverse
bn220 mount
thingiverse
free
MICROLONGRANGE IMMORTAL T GPS MOUNT by tszhinfpv
...v
thingiverse
some immortal t mount & gps mount for microlongrange frame
immortal t mount with cam mount for 25mm m2 stanoff
thingiverse
free
MicroLongRange Arm Brace by ItsMeAubey
... itsmeaubey
thingiverse
an arm brace for the #projectmicrolongrange.
all microlr frames from cncmadness now include this brace.
thingiverse
free
Project #MicroLongRange (4Inch) by Pskelton330
...or knife for sliding the wires in (see picture)
if you have any suggestions how i might improve these designs please let me know.
thingiverse
free
Microlongrange Matek GPS/CRSF Mount + SMA Mount by Preloi
...rossfire immortal antenna + mount for the sma pigtail
fits on the microlongrange 5 inch version.
printed with extrudr tpu medium,
thingiverse
free
MicroLongRange for 16x16-20x20-WhoopFC by schmidda
...required hardware
6x m2 20mm standoff
2x m2 25mm standoff
4x m2 nut
12x m2x6 steel screw
4x m2x8 steel screw
4x m2x16 steel screw
thingiverse
free
MicroLongRange 4" 3D parts by BAM_FPV
...elp bed adhesion).
arm protectors.
(no supports required - increase z height ration a little to ensure they fit over arms)
enjoy
Inav
thingiverse
free
INAV logo for flying wing
...inav logo for flying wing
thingiverse
this is a variant of the inav flight controller software logo for flying wing pilots.
thingiverse
free
iNav Wing Logo Keychain
...inav wing logo keychain
thingiverse
simple inav wing logo for keychain or stencil. included is svg and fusion 360 files.
thingiverse
free
MT Cradle iNav FC Mount by osgibson
...radle inav fc mount by osgibson
thingiverse
a remix of mochanic's mini talon cradle for a standard 30.5mm fc stack for inav.
thingiverse
free
simplified Sculptris Dummies by inav
...ed version of the sculptris dummies by dutchmogul. hopefully they will be easier to manipulate in simple programs like tinkercad.
thingiverse
free
FR7 INAV GPS Puck Mount System
... gps puck mount plate and a .10" diameter carbon rod to mount your gps puck for inav. print from tpu at 230*. use supports.
thingiverse
free
Simplified Sculptris OBJ Bits: Fantasy Shirts by inav
...simplified sculptris obj bits: fantasy shirts by inav
thingiverse
simplified versions of dutchmogul's fantasy shirts.
thingiverse
free
Fr7 flat BN-880 mount for inav + vista + TBS bardpole rear mount by KenjiFPV
... mount for inav + vista + tbs bardpole rear mount by kenjifpv
thingiverse
fr7 flat bn-880 mount for inav + vista + tbs bardpole
thingiverse
free
Simplified Sculptris OBJ Bits: Hairstyles by inav
...s: hairstyles by inav
thingiverse
these are some of dutchmogul's hairstyles, just simplified for use in low-res prints, etc.
thingiverse
free
Simplified Sculptris OBJ bits: Pants and Skirts by inav
... skirts by inav
thingiverse
these are just lower-res versions of dutchmogul's collection of fantasy pants and skirts. enjoy!
thingiverse
free
GPS SUPPORT INAV FLIGHT by malpom
....com/it/7m8m-ublox-m8n-gps-module-for-apm-pixhawk-cc3d-naze32-f3-flight-control-p-1078657.html?rmmds=myorder&cur_warehouse=cn