Thingiverse
Marconi SELEX PRR dummy (PTT) by igdrassil
by Thingiverse
Last crawled date: 3 years, 4 months ago
Personal Role Radio - Dummy PTT
Русская версия
English
Description
This is a replica of a Marconi/Selex H4855 radio AKA Personal Role Radio.
Consists of two parts - main empty "box" with holes and buttons box (PTT box) and they screw to one aonther with a metal screw just as original radio parts are. This replica might be used in a multiple ways. The easiest and most useful one - to make a PTT box for a portable radio, wihich can then be used with original (or chinese knockoff) headset.
You can choose to make PTT for either one-channel radio (such as Baofeng UV-B5, Yaesu, Motorola), or "two channel" (in fact, radio with two ptt buttons, i.e Baofeng UV-82 or Zastone A-19).
Main "box" might contain some electronics as well (volume control or even whole mini-radio). It has a functional battery compartment as well as holes for volume control, channel selector and antenna. Or you can just glue the external parts.
PTT box exists in four varieries. Two of them are single-button, and dual-button and each of these are either for LEMO connector or for a russian military-grade PC4 connector. The latter one is best for chinese Bowman headset replicas, cause it is easy to solder and is much cheaper in Russia than even chinese LEMO-compatible connectors.
You can see all my replicas compared to original radio (on top of them) on picture P0.
Printable parts
Body front.stl - main box front part.
Body back.stl - main box rear part.
Body insert.stl - glueable battery compartment battery guide (if you'd like to made functional compartment).
Body lid.stl - battery compartment lid.
Knob volume.stl - volume knob, for a RV097NS potentiometer.
Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio.
Antenna.stl - old-style, PRR mock antenna.
Antenna New.stl - new style, EZ-PRR mock antenna.
PTT Lemo Single.stl - PTT module, single button, Lemo.
PTT Lemo.stl - PTT module, dual button,Lemo.
PTT PC4 Single.stl - PTT module, single button, PC4.
PTT PC4.stl - PTT module, dual button, PC4.
For partially assembled see pictures P1, P2, P3.
P4 picture is an assembled previous generation replica.
Additional parts
See picture P4 for some details photos.
Square button, 12mm.
Round button, 12мм.
Connector Lemo (clone, EGG 1B or better ECG 1B, 5-pin), or PC4.
Flat slot screw М5х16 (might be sligtly longer).
Cable to connect to radio or inexpensive radio headset (only cable needed).
Potentiometer RV097NS an 16-position encoder (optional).
Print settings
Most parts are made from ABS, as it is easy to grind/polish and has a good adhesion. And it is strong enough for this particular replica.
The only exceptions is antenna(s). You need to print it from flexible material, TPU for example, otherwise they will be too stoff and will break easily. But if you are stubborn enough to print it with ABS/PETG, glue some metal or glass/carbon-fiber rod into hole in the antenna.
Material - ABS/Flex
Nozzle - 0.3 mm
Layer - 0.15 mm
Infill - 40%
Top/bottom - 5-6 layers
Walls - 4-5 layers
Actually, it's best to print knobs with a photopolymer priner. I got exceptionally good results with my Elegoo Mars Pro and black Anycubic Eco resin.
Assembly
Clean the part thoroughly from supports, then lap/grind them with a filer. Ensure they join without play and you do not have to force them to do so. Be polite.
Apply putty and let dry (optional)
Grind and polish (imho this step is inevitable)
Apply primer and let dry
Apply paint (I found Focso Olive Drab to be very close to original radios) and let dry
I mean it, let it dry completely
Install electrical parts to main box
Insert battery compartment lid in its place and glue the main box rear part.
Attach knobs (or just glue them on box).
Glue the mock antenna
If you are maiking PTT then drill the bottom of the PTT box and glue the radio cable into it (there is a blind hole inside the PTT box).
Install buttons and headset connector, wire it
Screw the PTT onto the main box.
Print provided decals (600dpi), cut and glue (preferrably use self adhesive)
Profit!
Russian
Описание
Реплика радиостанции Marconi/Selex H4855, она же Personal Role Radio.
Представляет собой полый корпус с отверстиями и модуль кнопок, который прикручивается к основному корпусу с помощью винта (как у оригинальной рации). Макет может быть "задействован" множеством способов. Наиболее простой и универсальный - сделать из неё эдакую кнопку для радиостанции, к которой можно подключить оригинальную (или не очень оригинальную) гарнитуру.
По желанию может быть изготовлена как под одноканальную рацию (Baofeng UV-B5, Yaesu, Motorola), либо под двухкнопочную вроде Baofeng UV-82 или Zastone A-19.
Основной блок может как не содержать электроники, так и оборудован действующим батарейным отсеком, есть место под установку регулятора громкости, селектора каналов, антенны. А можно все эти элементы просто приклеить.
Блок кнопок представлен в четырех вариантах. Два вида - однокнопочный или двухкнопочный. Каждый из видов - либо под разъем Lemo B01 (или его китайский аналог), либо под русский военный разъем РС4, который в целом неплохо заменяет LEMO. Главное, его легко припаять к китайской реплике гарнитуры Bowman и комплект даже с нашими жадными продавцами здорово дешевле комплекта LEMO.
Печатные детали
Body front.stl - основная часть корпуса.
Body back.stl - задняя часть корпуса.
Body insert.stl - деталь для вклеивания в батарейный отсек (если хочется его сделать функциональным).
Body lid.stl - крышка батарейного отсека.
Knob volume.stl - крутилка регулятора громкости, под потенциометр RK07 со "звездчатой" крутилкой.
Knob channel.stl - крутилка выбора канала, под 16-позиционный переключатель канальной рации, модель не знаю.
Antenna.stl - антенна старого образца, от PRR.
Antenna New.stl - антенна нового образца, от EZ-PRR.
PTT Lemo Single.stl - блок кнопок, однокнопочный под разъем Lemo.
PTT Lemo.stl - блок кнопок, двухкнопочный под разъем Lemo.
PTT PC4 Single.stl - блок кнопок, однокнопочный под разъем PC4.
PTT PC4.stl - блок кнопок, двухкнопочный под разъем PC4.
Собранный корпус - см. фото P1, P2, P3.
На фото P4 - полностью собранная реплика предыдущего поколения.
Дополнительные детали
См. рисунок P5, хоть там и не всё.
Кнопка квадратная, посадочное место 12мм.
Кнопка круглая, посадочное место 12мм.
Разъем (клон) Lemo EGG 1B или лучше ECG 1B, 5-контактов, либо PC4.
Винт с плоской головкой, шлицевой М5х16 (можно длиннее, но не стоит).
Кабель или недорогая гарнитура-донор.
Регулятор громкости RV097NS и 16-позиционный переключатель (опционально).
Параметры печати
Основной материал печати - ABS, т.к. он хорошо шлифуется и достаточно прочен для данной модели.
Исключение - антенны. Для них необходимо применить Flex, т.к. иначе они будут жесткими и ломкими. Если все же вы решили сделать их также из ABS/PETG, то в моделях сделано отверстие, в которое можно вклеит спицу из металла, стекловолокна или карбона.
Материал - ABS/Flex
Сопло - 0.3 мм
Слой - 0.15 мм
Заполнение - 40%
Верх/низ - 5-6 слоев
Стенки 4-5 слоев
В идеале напечатать ручки на фотополимерном принтере. На моем Elegoo Mars Pro из смолы Anycubic Eco черного цвета они получились зашибись.
Сборка
Тщательно очистить детали, подогнать так, чтобы собирались без излишнего приложения силы (плотно, но не чересчур).
Шпатлевка внешних поверхнстей и сушка (опционально)
Шлифовка внешней поверхности (имхо неизбежный шаг)
Грунтовка и сушка
Покраска (использую Focso Olive Drab) и сушка
Оставляем реально полностью высохнуть
Вкручиваем внутренние элементы в основную часть корпуса, провода выводим в отверстие.
Приклеиваем заднюю часть, одновременно присоединив крышку
Надеваем крутилки (или приклеиваем их).
Приклеиваем антенну
Если делаем PTT - сверлим отверстие в нижней части блока кнопок, вклеиваем туда конец провода гарнитуры
Монтируем электронику в кнопку
Прикручиваем модуль кнопок к корпусу рации.
Печатаем деколи, вырезаем, наклеиваем (лучше всего печатать на белой матовой пластиковой самоклейке).
Профит!
Русская версия
English
Description
This is a replica of a Marconi/Selex H4855 radio AKA Personal Role Radio.
Consists of two parts - main empty "box" with holes and buttons box (PTT box) and they screw to one aonther with a metal screw just as original radio parts are. This replica might be used in a multiple ways. The easiest and most useful one - to make a PTT box for a portable radio, wihich can then be used with original (or chinese knockoff) headset.
You can choose to make PTT for either one-channel radio (such as Baofeng UV-B5, Yaesu, Motorola), or "two channel" (in fact, radio with two ptt buttons, i.e Baofeng UV-82 or Zastone A-19).
Main "box" might contain some electronics as well (volume control or even whole mini-radio). It has a functional battery compartment as well as holes for volume control, channel selector and antenna. Or you can just glue the external parts.
PTT box exists in four varieries. Two of them are single-button, and dual-button and each of these are either for LEMO connector or for a russian military-grade PC4 connector. The latter one is best for chinese Bowman headset replicas, cause it is easy to solder and is much cheaper in Russia than even chinese LEMO-compatible connectors.
You can see all my replicas compared to original radio (on top of them) on picture P0.
Printable parts
Body front.stl - main box front part.
Body back.stl - main box rear part.
Body insert.stl - glueable battery compartment battery guide (if you'd like to made functional compartment).
Body lid.stl - battery compartment lid.
Knob volume.stl - volume knob, for a RV097NS potentiometer.
Knob channel.stl - channel knob, for 16 position rotary encoder, model unknown, mine was from professional 16-ch radio.
Antenna.stl - old-style, PRR mock antenna.
Antenna New.stl - new style, EZ-PRR mock antenna.
PTT Lemo Single.stl - PTT module, single button, Lemo.
PTT Lemo.stl - PTT module, dual button,Lemo.
PTT PC4 Single.stl - PTT module, single button, PC4.
PTT PC4.stl - PTT module, dual button, PC4.
For partially assembled see pictures P1, P2, P3.
P4 picture is an assembled previous generation replica.
Additional parts
See picture P4 for some details photos.
Square button, 12mm.
Round button, 12мм.
Connector Lemo (clone, EGG 1B or better ECG 1B, 5-pin), or PC4.
Flat slot screw М5х16 (might be sligtly longer).
Cable to connect to radio or inexpensive radio headset (only cable needed).
Potentiometer RV097NS an 16-position encoder (optional).
Print settings
Most parts are made from ABS, as it is easy to grind/polish and has a good adhesion. And it is strong enough for this particular replica.
The only exceptions is antenna(s). You need to print it from flexible material, TPU for example, otherwise they will be too stoff and will break easily. But if you are stubborn enough to print it with ABS/PETG, glue some metal or glass/carbon-fiber rod into hole in the antenna.
Material - ABS/Flex
Nozzle - 0.3 mm
Layer - 0.15 mm
Infill - 40%
Top/bottom - 5-6 layers
Walls - 4-5 layers
Actually, it's best to print knobs with a photopolymer priner. I got exceptionally good results with my Elegoo Mars Pro and black Anycubic Eco resin.
Assembly
Clean the part thoroughly from supports, then lap/grind them with a filer. Ensure they join without play and you do not have to force them to do so. Be polite.
Apply putty and let dry (optional)
Grind and polish (imho this step is inevitable)
Apply primer and let dry
Apply paint (I found Focso Olive Drab to be very close to original radios) and let dry
I mean it, let it dry completely
Install electrical parts to main box
Insert battery compartment lid in its place and glue the main box rear part.
Attach knobs (or just glue them on box).
Glue the mock antenna
If you are maiking PTT then drill the bottom of the PTT box and glue the radio cable into it (there is a blind hole inside the PTT box).
Install buttons and headset connector, wire it
Screw the PTT onto the main box.
Print provided decals (600dpi), cut and glue (preferrably use self adhesive)
Profit!
Russian
Описание
Реплика радиостанции Marconi/Selex H4855, она же Personal Role Radio.
Представляет собой полый корпус с отверстиями и модуль кнопок, который прикручивается к основному корпусу с помощью винта (как у оригинальной рации). Макет может быть "задействован" множеством способов. Наиболее простой и универсальный - сделать из неё эдакую кнопку для радиостанции, к которой можно подключить оригинальную (или не очень оригинальную) гарнитуру.
По желанию может быть изготовлена как под одноканальную рацию (Baofeng UV-B5, Yaesu, Motorola), либо под двухкнопочную вроде Baofeng UV-82 или Zastone A-19.
Основной блок может как не содержать электроники, так и оборудован действующим батарейным отсеком, есть место под установку регулятора громкости, селектора каналов, антенны. А можно все эти элементы просто приклеить.
Блок кнопок представлен в четырех вариантах. Два вида - однокнопочный или двухкнопочный. Каждый из видов - либо под разъем Lemo B01 (или его китайский аналог), либо под русский военный разъем РС4, который в целом неплохо заменяет LEMO. Главное, его легко припаять к китайской реплике гарнитуры Bowman и комплект даже с нашими жадными продавцами здорово дешевле комплекта LEMO.
Печатные детали
Body front.stl - основная часть корпуса.
Body back.stl - задняя часть корпуса.
Body insert.stl - деталь для вклеивания в батарейный отсек (если хочется его сделать функциональным).
Body lid.stl - крышка батарейного отсека.
Knob volume.stl - крутилка регулятора громкости, под потенциометр RK07 со "звездчатой" крутилкой.
Knob channel.stl - крутилка выбора канала, под 16-позиционный переключатель канальной рации, модель не знаю.
Antenna.stl - антенна старого образца, от PRR.
Antenna New.stl - антенна нового образца, от EZ-PRR.
PTT Lemo Single.stl - блок кнопок, однокнопочный под разъем Lemo.
PTT Lemo.stl - блок кнопок, двухкнопочный под разъем Lemo.
PTT PC4 Single.stl - блок кнопок, однокнопочный под разъем PC4.
PTT PC4.stl - блок кнопок, двухкнопочный под разъем PC4.
Собранный корпус - см. фото P1, P2, P3.
На фото P4 - полностью собранная реплика предыдущего поколения.
Дополнительные детали
См. рисунок P5, хоть там и не всё.
Кнопка квадратная, посадочное место 12мм.
Кнопка круглая, посадочное место 12мм.
Разъем (клон) Lemo EGG 1B или лучше ECG 1B, 5-контактов, либо PC4.
Винт с плоской головкой, шлицевой М5х16 (можно длиннее, но не стоит).
Кабель или недорогая гарнитура-донор.
Регулятор громкости RV097NS и 16-позиционный переключатель (опционально).
Параметры печати
Основной материал печати - ABS, т.к. он хорошо шлифуется и достаточно прочен для данной модели.
Исключение - антенны. Для них необходимо применить Flex, т.к. иначе они будут жесткими и ломкими. Если все же вы решили сделать их также из ABS/PETG, то в моделях сделано отверстие, в которое можно вклеит спицу из металла, стекловолокна или карбона.
Материал - ABS/Flex
Сопло - 0.3 мм
Слой - 0.15 мм
Заполнение - 40%
Верх/низ - 5-6 слоев
Стенки 4-5 слоев
В идеале напечатать ручки на фотополимерном принтере. На моем Elegoo Mars Pro из смолы Anycubic Eco черного цвета они получились зашибись.
Сборка
Тщательно очистить детали, подогнать так, чтобы собирались без излишнего приложения силы (плотно, но не чересчур).
Шпатлевка внешних поверхнстей и сушка (опционально)
Шлифовка внешней поверхности (имхо неизбежный шаг)
Грунтовка и сушка
Покраска (использую Focso Olive Drab) и сушка
Оставляем реально полностью высохнуть
Вкручиваем внутренние элементы в основную часть корпуса, провода выводим в отверстие.
Приклеиваем заднюю часть, одновременно присоединив крышку
Надеваем крутилки (или приклеиваем их).
Приклеиваем антенну
Если делаем PTT - сверлим отверстие в нижней части блока кнопок, вклеиваем туда конец провода гарнитуры
Монтируем электронику в кнопку
Прикручиваем модуль кнопок к корпусу рации.
Печатаем деколи, вырезаем, наклеиваем (лучше всего печатать на белой матовой пластиковой самоклейке).
Профит!
Similar models
thingiverse
free
BAOFENG UV-5R PTT BUTTON COVER by PARADOXICLES
...with your favorite glue ( reccomend e-6000 or b-6000)
baofeng uv-5r volume knob cover - https://www.thingiverse.com/thing:4889776
thingiverse
free
Baofeng Radio PTT button by mi540i
...acements.
picture is of a version with raised text, the stl is not branded.
must be printed out of flexible material. i used tpu.
thingiverse
free
BAOFENG UV-5R VOLUME KNOB COVER by PARADOXICLES
... circular part around the base of
the knob and antenna
baofeng uv-5r ptt button cover - https://www.thingiverse.com/thing:4889778
thingiverse
free
TEA-like U94 dual PTT by igdrassil
...аем скобу под стропу, вырезом к себе, заводим стропу в вырез и прикручиваем ptt к скобе парой винтов м3. быстро, просто, надёжно.
thingiverse
free
Baofeng UV5R safe knob by maldacr
...ents unwanted on/off or volume change on baufeng uv5r.
use super glue (or equiv) to attach outer part to radio body.
spring 6x15.
3ddd
free
Тумба под телевизор Opus
...ский дизайн. они выглядят очень лаконично и сдержанно, но при этом их оригинальность просто не может не привлечь к себе внимание.
thingiverse
free
Anet A8 bowden extruder block for PC4-01 pneumatic fitting by UtconoSS
...m6, и я смоделировал блок для фиттинга pc4-01(такой же как и на e3d v6). наверное, даже получится печатать флексами (не проверял)
thingiverse
free
Baofeng UV-5R Case by mwhite
...s all buttons and keys. the radio is held in place by the belt clip that latches onto the back of the case. print at full size.
thingiverse
free
Baofeng UV-5R and PTT Holder by M4NUXWORKSHOP
...ng uv-5r and ptt holder by m4nuxworkshop
thingiverse
baofeng uv-5r and ptt desktop holder.
*not compatible with extended battery
3ddd
$1
Подставка под цветы "Экспо-Древ"
...p;quot;
3ddd
подставка
подставка для цветов или других предметов декора и интерьера. в архиве также есть светлая текстура дерева.
Selex
3d_export
$80
Radar Gripen 3D Model
...radar gripen 3d model 3dexport radar gripen aesa plate selex galileo nose aircraft fighter war tilting radar gripen 3d...
cg_trader
$6
Selex Radio - Tutorial Included
...selex radio - tutorial included
cg trader
tutorial here: https://www.youtube.com/channel/uc3r6ldf-rlb9qw-d3cnhr7w
grabcad
free
Personal Role Radio
...personal role radio grabcad made by selex operates on 2.4+ ghz. the standard british army radio...
cg_trader
$100
Radar Gripen
...for a magazine infographics about new radar technology of selex galileo with tilting flat plate aesa for side radar...
3dwarehouse
free
CİRİT 2.75” LAZER GÜDÜMLÜ FÜZE (LASER MANAGED MISSILES)
...platformuna entegre edilmiş ve belli dinamikler altında etkinliğini kanıtlamıştır. selex ile falco insansız hava platformu’na entegrasyon çalışmaları devam etmektedir....
Igdrassil
thingiverse
free
Element LLM01 flashlight front bezel by igdrassil
...asy to sand).
0.3 mm nozzle / 0.15 mm layer heigh.
лучше печатать из abs (проще обрабатывать).
ноззл 0.3 мм, высота слоя 0.15 мм.
thingiverse
free
SureFire flash hider by igdrassil
...ь, прочистить резьбу.
две версии на резьбу 14мм - левая (l) и правая (r) резьба (буквы l и r указаны в конце названия stl файла).
thingiverse
free
Element LLM01 mode switch knob by igdrassil
...учшенная в мои ручонки еще не попадала).
возможно, придется чуть подпилить ось переключателя для полной посадки.
печатал из petg.
thingiverse
free
Picattiny 19mm riser by igdrassil
... сопло 0.4 мм, стены/верх/низ 4-6, заполнение 40-45%. печать с поддержками, передней частью вверх (или, если вы верующий - вниз).
thingiverse
free
G&G auto-tracer unit back for -14mm thread by igdrassil
...ный задник с левой резьбой 14 мм для использования трассерной насадки g&g с разными страйкбольными приводами. печатал из abs.
thingiverse
free
Heavy gas block for canadian/british M4 by igdrassil
...печатал из abs. лишние отверстия для стевлоколоконных стержней или стальных шпилек.
мушку переставить со страйкбольного газблока.
thingiverse
free
R-187-P1 Azart - headset remote (PU) dummy by igdrassil
...му типа подключается проводом рация и к нему уже подключается гарнитура, а также внешние ништяки типа зарядника/внешнего питания.
thingiverse
free
M249 front sight post repair for airsoft (Classic Army) by igdrassil
...о поддержки.
зачистить после распечатки, пройти резьбы метчиками м3 и м5, перенести мушку и фиксирующий винт из сломанной стойки.
thingiverse
free
SF Self-locking silencer for airsoft by igdrassil
... мм;
слой 0.2 мм;
заполнение 40% (в идеале сотовое);
верх/низ - 5;
стены - 4.
сборка
прочистить резьбы, скрутить как на рисунках.
thingiverse
free
Azart - antenna relocator "Protivoves" by igdrassil
...есто пайки герметиком, иначе кабель будет насасывать воду при погружении в оную или под сильным дождем.
дальше см. по ссылке выше
Prr
turbosquid
$59
PRR Lowpoly kitten statuette
...odel prr lowpoly kitten statuette for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1385838)
thingiverse
free
PRR F-22 Flatcar by Professorburnout
...added a part that can be used to extend this flatcar to make it a prr fm style flat car.https://www.thingiverse.com/thing:3335716
thingiverse
free
PRR F-22 Flatcar HO by konrads3
...upler box as retainer, cut to size.
thank you professorburnout for the g scale initial one, i wish mine looked as good as yours !
thingiverse
free
G Scale Bulk Container for Gondola by randymower
...10 (two more in the middle) in a gondola. prr also used a similar...
thingiverse
free
Freight Car Truck 2E-F10 by Professorburnout
...thingiverse this truck was designed to go with the prr f-22 flat car i postedhttp://www.thingiverse.com/thing:2069464 i used 3mm stainless...
grabcad
free
PRR Rail section
...prr rail section
grabcad
prr rail section
cg_trader
$60
PRR Stock Car
...prr stock car
cg trader
prr stock car
cg_trader
$60
PRR Baggage Car
...prr baggage car
cg trader
prr baggage car
cg_trader
$60
PRR Passenger Car
...prr passenger car
cg trader
prr passenger car
Marconi
3d_export
$49
Bologna Guglielmo Marconi Airport 10km
...bologna guglielmo marconi airport 10km
3dexport
3ddd
$1
MARCONI CAGED PENDANT
...n hardware
https://www.restorationhardware.com/catalog/product/product.jsp?productid=prod2460325&categoryid;=search
turbosquid
$5
Hanging lamp Red Filament Marconi Cage
...i red filament marconi cage for download as max, fbx, and obj on turbosquid: 3d models for games, architecture, videos. (1573204)
3dbaza
$9
Stroller BeBe-mobile Marconi BE4 (122879)
...oni stroller 3d model<br>corona renderer 2 (final)<br>bebe-mobile marconi be4<br>(shock.link + shock.perf.link)
3d_sky
free
MARCONI CAGED PENDANT
...toration hardware
https://www.restorationhardware.com/catalog/product/product.jsp?productid=prod2460325&categoryid=search
3dbaza
$3
Hanging lamp Romatti Red Filament Marconi Cage (116448)
...6448)
3dbaza
romatti red filament marconi cage hanging lamp 3d model.<br>the model includes: .max, .fbx, .mtl, .obj files.
thingiverse
free
Star Trek US Marconi class 1:2000 by outcastrc
...e for printing. scaled to 1:2000
find this model and more here on his deviantart page: http://metlesitsfleetyards.deviantart.com/
3dbaza
$3
MARCONI TUFTED BLACK LEATHER ACCENT SOFA (347057)
...;br>xform: yes<br>box trick: yes<br>model parts: 2<br>render: v-ray<br>formats: 3ds max 2014, obj, fbx
thingiverse
free
BBC Marconi-Reisz Microphone by TinBoxTelevision
...atly, but it suits my needs just fine.
scale it up to around 10, since inventor sucks with exporting the correct sized stl files.
Ptt
turbosquid
$37
PTT Design Ascot Elbow Chair
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
thingiverse
free
PTT mailbox (Dutch)
...ptt mailbox (dutch)
thingiverse
the original dutch ptt mailbox
thingiverse
free
PTT bowman button by markus22rus
...ptt bowman button by markus22rus
thingiverse
ptt bowman button
thingiverse
free
PTT Switch Case by tdeagan
...ptt switch case by tdeagan
thingiverse
this is a hand-mounted case for a ham radio ptt swtich.
thingiverse
free
PTT (KPN) Afdekplaat by jwveldhuis
...pn) afdekplaat by jwveldhuis
thingiverse
cover plate for a telephony wall box used in the netherlands by ptt telecom in the 80s.
thingiverse
free
Abbree PTT tangent Holder by Grind3x
...abbree ptt tangent holder by grind3x
thingiverse
abbree ar-780 ptt tangent holder
thingiverse
free
Baofeng UV-5R and PTT Holder by M4NUXWORKSHOP
...ng uv-5r and ptt holder by m4nuxworkshop
thingiverse
baofeng uv-5r and ptt desktop holder.
*not compatible with extended battery
thingiverse
free
Firefighting PTT cable tidy and helmet clip by Mo22is
... tidy attached to the webbing strip of firefighting tunic/coat. the firefighting helmet comms is connected to the ptt hand piece.
thingiverse
free
Sena SR10 - PTT Preventer by omninate
...rts
slide the sena sr10 into the 3d-printed enclosure
secure the enclosure to the rear of the sr10 with four m3x8 machine screws.
thingiverse
free
Vertex / Yaesu FTH 2009 PTT by axel_becchi
...is a reeplace for the ptt butom for yaesu / vertex handie, it requieres a little bit of sand after print, print at 40 mm/s speed.
Dummy
archibase_planet
free
Dummy
...dummy
archibase planet
mannequin dummy
dummy n100111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
3d_export
$18
women-dummy
...women-dummy
3dexport
just dummy
turbosquid
$10
Dummy
...quid
royalty free 3d model dummy for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1403647)
archive3d
free
Dummy 3D Model
...archive3d
mannequin dummy
dummy n100111 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archive3d
free
Dummy 3D Model
...d model
archive3d
dummy
dummy 1 n150408 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
archive3d
free
Dummy 3D Model
...rchive3d
mannequin dummy
dummy n160408 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
turbosquid
$30
Target Dummy
...squid
royalty free 3d model target dummy for download as fbx on turbosquid: 3d models for games, architecture, videos. (1437335)
3d_export
$5
jarde-dummy-1snapshot9
...jarde-dummy-1snapshot9
3dexport
jarde-dummy-1.snapshot.9
turbosquid
$130
crash dummy
...
royalty free 3d model crash dummy for download as ma and obj on turbosquid: 3d models for games, architecture, videos. (1216074)
3d_export
$20
Dummy 3D Model
... character artists model man woman human wood posable puppet jointed pose humanoid body
dummy 3d model rendersteel 75948 3dexport