khadas vim3 case

...khadas vim3 case hexagon style by nonrar thingiverse i modified a little to have the appearance of a hexagon

...khadas vim3 hexagon by nonrar thingiverse i modified a little to have the appearance of a hexagon

... this is a prototype design! i do not have the computer, although i would like to get one in the near future to actually test it.

.... khadas logo used on the cover plate with the logo used as vent holes and the original "khadas" typeface on the front.

...it a separate part too, so you could easily replace it with your own model. all important sizes where measured on actual camera.

... there are some vent holes on the sides for better airflow. the board is held in case by the included nuts on the rca connectors.

... board are screwed tight. in my case, i decided to have the front cut out of an acrylic piece to match the looks of my amplifier.

...idges bellow the nvme spring so that it moves a bit. future work rack mount for the threaded rod and spring holders between nodes

...d and there are cheap $5+/- curve to direct air flow under the pcb also. plenty of room for cables and some custom boards. thanks

...ca connectors are, it might tip over a bit. note: use the 3mf files if you can, the stls are just there to keep thingiverse happy

...khadas vim3 hexagon by nonrar thingiverse i modified a little to have the appearance of a hexagon

...khadas vim3 case hexagon style by nonrar thingiverse i modified a little to have the appearance of a hexagon

... this is a prototype design! i do not have the computer, although i would like to get one in the near future to actually test it.

...idges bellow the nvme spring so that it moves a bit. future work rack mount for the threaded rod and spring holders between nodes

...it a separate part too, so you could easily replace it with your own model. all important sizes where measured on actual camera.

...khadas vim3 hexagon by nonrar thingiverse i modified a little to have the appearance of a hexagon

...khadas vim3 case hexagon style by nonrar thingiverse i modified a little to have the appearance of a hexagon

... this is a prototype design! i do not have the computer, although i would like to get one in the near future to actually test it.

.... khadas logo used on the cover plate with the logo used as vent holes and the original "khadas" typeface on the front.

... board are screwed tight. in my case, i decided to have the front cut out of an acrylic piece to match the looks of my amplifier.

...ca connectors are, it might tip over a bit. note: use the 3mf files if you can, the stls are just there to keep thingiverse happy

... there are some vent holes on the sides for better airflow. the board is held in case by the included nuts on the rca connectors.

...d and there are cheap $5+/- curve to direct air flow under the pcb also. plenty of room for cables and some custom boards. thanks

...r supports i used a lot but only because i printed mine in the upright position to retain a uniform surface on all visible faces.

...case 3dexport case

...case archibase planet showcase show-case glass case glass-case + cakes - 3d model for interior 3d visualization.

...case archibase planet showcase show-case glass case glass-case for chips - 3d model for interior 3d visualization.

...case archibase planet case shelving drawer case - 3d model for interior 3d visualization.

...case archibase planet case rack locker case - 3d model for interior 3d visualization.

...case archibase planet case drawer kitchen furniture case - 3d model for interior 3d visualization.

...case archibase planet case cupboard shelving glass case - 3d model for interior 3d visualization.

...case archibase planet case handbag suitcase case - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...case archibase planet case suitcase case 5 - 3d model (*.gsm+*.3ds) for interior 3d visualization.

...case archibase planet locker case dresser case - 3d model (*.gsm+*.3ds) for interior 3d visualization.