Thingiverse
Gimbal by Nickk1997
by Thingiverse
Last crawled date: 3 years, 1 month ago
This gimbal is a part of project i have been working on at school. the gimbal is designed by me and my fellow students (group of 4). and we have worked with the mechanics, eletronics and the software.
we put a GoPro on it because we would be sure that we could use it for test, as we didnt have time to play around to fit a DSLR on it
The Gimbal could benefit from some minor modifications. here by bigger motors for Yaw and Roll. but also general strength.
Parts list:
Turnigy_HD_5208http://www.hobbyking.com/hobbyking/store/__45369__Turnigy_HD_5208_Brushless_Gimbal_Motor_BLDC_.html
12mm aluminium tube
16mm aluminium tube
2,5 mm bolts
3 mm bolts
5mm bolts and nuts
3mm aluminium plate
2 IMU's
Gimbal controller (We developed our own, if you would be interested in this write me.) otherwise it can probably be adapted to any other controller on the marked.
LIPo og likewise (we used a LiFePo4 battery because our school wont allow the use of LiPo's
we put a GoPro on it because we would be sure that we could use it for test, as we didnt have time to play around to fit a DSLR on it
The Gimbal could benefit from some minor modifications. here by bigger motors for Yaw and Roll. but also general strength.
Parts list:
Turnigy_HD_5208http://www.hobbyking.com/hobbyking/store/__45369__Turnigy_HD_5208_Brushless_Gimbal_Motor_BLDC_.html
12mm aluminium tube
16mm aluminium tube
2,5 mm bolts
3 mm bolts
5mm bolts and nuts
3mm aluminium plate
2 IMU's
Gimbal controller (We developed our own, if you would be interested in this write me.) otherwise it can probably be adapted to any other controller on the marked.
LIPo og likewise (we used a LiFePo4 battery because our school wont allow the use of LiPo's
Similar models
grabcad
free
Square Tubing Cap with Bolt Organizers
...ould be nice to have a place to put them like this cap organizer, unfortunately we don't have a 3d printer but if we did.....
3dwarehouse
free
I have an idea for LFC313 {16Kb}
...go, you do the website, then give me the ability to control it, and we improve it. ok? #airways #flyhigh #lfc313 #royal #somthing
grabcad
free
Manfrotto T Clamp
...n fibre, will probably have to use thinner tubes though. just waiting for a couple of flanged 35mm bearings to clamp in the hole.
thingiverse
free
Bolt and nut by PinoCAD
...with resin printer, because of the better quality of layer, otherwise the thread could not match.
if you enjoy it, please tip me!
thingiverse
free
Walkera G2d Gimbal to GoPro Fig Rig by Droneme
...a mount i have printed. just remove the 2 hex bolts from the gimbal and use those same bolts to mount the gimbal to the adapter.
thingiverse
free
CG035 Gimbal Mk IV by cj7hawk
...well.
also needed on this are some bearings and servos and a few wires, but it should all come together to make a working gimbal.
thingiverse
free
Feiyu holder for GoPro by guytc
...in the holder
screw the bottom part on the top part of the gimbal
my first try was not successful, but this try is working fine.
grabcad
free
Ivica's models
...ivica's models
grabcad
these models work in the school because they are very interesting to me.
grabcad
free
Bike Phone Bracket
... phone bracket
grabcad
it uses 9.6 mm aluminium tubes. just put the phone inside and tight the knob.
worked really well for me.
thingiverse
free
Bed support for Ender 5 by Warlo
.... it uses a way less filament than other similar parts but it's really lightweight and strong. extra parts:...
Nickk1997
thingiverse
free
Snowboard mount by Nickk1997
... any on the marked that fitted my needs. i wanted it to be low profile but still be able to fit a led strip behind the snowboard.
thingiverse
free
Ski wallmount by Nickk1997
... i made this design.
the design is designed for his skis, but just ask if you want the file, or want me to adapt it to your needs
thingiverse
free
Drift Trike Wheel by Nickk1997
...obs pretty big print for my setiing almost 650 grams of filament where used
tested them and did 55 kph and it didnt feel sketchy
thingiverse
free
Skateboard holder by Nickk1997
...olution out there that made the skateboard easy to remove, that also showed the underside of the board when it was just hanging.
Gimbal
turbosquid
$1
Yuneec Save Stick for Gimbal
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$20
splashdrone gimbal camera
...nsions. all textures used have been included. thank you for purchasing this model!! click on my username to see more of my models
3d_export
$40
splashdrone 3 plus with gimbal camera
...nsions. all textures used have been included. thank you for purchasing this model!! click on my username to see more of my models
turbosquid
$88
DJI Phantom 2 Quadcopter with gimbal for GoPro HERO4 or 3
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
3d_export
$5
concentrate box
...concentrate box 3dexport concealer box with handle and gimbal ...
cg_studio
$55
Drone Quadrocopter With Camera Rigged3d model
...fly wing propeller rc video camera sky dron spy gimbal gopro riged aircraft toy .obj .fbx .max .3ds -...
3d_ocean
$29
Drone Quadrocopter With Camera Rigged
...quadrocopter with camera rigged 3docean aircraft camera dron fly gimbal gopro propeller quadrocopter rc riged sky sport spy toy...
3ddd
free
Foucault's Iron Orb
...physicist léon foucault's gyroscope inspired our openwork globe. its double-gimbal frame is built of iron around a nucleus of...
thingiverse
free
Gimbal by tannermichael
...amera and gravity to self level. the gimbal uses .125" axles to pivot on. this gimbal was made using autodesk inventor 2015.
thingiverse
free
2020 Gimbal
...2020 gimbal
thingiverse
2020 gimbal