Caloi
free3d
$6
Mobilete Caloi 1991
...mobilete caloi 1991
free3d
linda mobilete modelada por jurugamer, agradeo pela preferencia :)
thingiverse
free
Base Ponteira Esteira Ergométrica by fabiano-morais
...by fabiano-morais thingiverse ponteira de rolete esteira universal (athletic, caloi act...
grabcad
free
Caloi 10
...caloi 10
grabcad
modelo 1979
grabcad
free
Mobilette Caloi 60cc
...por linhas do bom e velho solidworks, dísponível pra download para a partir da versão 2012 do software, espero que gostem, grato!
grabcad
free
Mobilette Caloi 60cc New Generation
...por linhas do bom e velho solidworks, dísponível pra download para a partir da versão 2012 do software, espero que gostem, grato!
cg_trader
$2
Bike 3D
...bike 3d cg trader bicicleta caloi em 3d blender modelagem junior dream blender bike bicicleta...
3dwarehouse
free
Caloy
...caloy
3dwarehouse
3dwarehouse
free
caloi sk fixa
...caloi sk fixa
3dwarehouse
3dwarehouse
free
clemente
...clemente 3dwarehouse caloi ...
Poti
thingiverse
free
Poti Holder by tophmann
... to screw it on a board. customize the scad file so it matches your poti size. default is 16.4mm diamenter and 9.2mm base height.
thingiverse
free
Poti Mount GBZ by atomant_
...poti mount gbz by atomant_
thingiverse
mount for poti to control volume. snap fit for the one i used.
thingiverse
free
Housing for QO-100 POTY-Patch antenna
...housing for qo-100 poty-patch antenna
thingiverse
housing for qo-100 poty-patch antenna in combination with dn 110 end cap
thingiverse
free
Simple Potentiometer (Poti) Holder by Gecko089
... is attached.
print time is about 30mins with support. i printed it solid, because it barely makes a difference in time and cost.
thingiverse
free
DC5GY-Feed POTY Adapter by 4ta
....
the used lnb holder is for kathrein dish and bought here:https://www.amazon.de/dp/b0052auu6w/ref=cm_sw_em_r_mt_dp_j4-pfb763p460
thingiverse
free
labeled poti knobs for overdrive pedal by pla_godX
... adapt it.
i added holes for m3 screw and nut.
largest outer diameter is <23mm. be aware of enough distance between the potis.
thingiverse
free
FrSky Horus X12S Menu Poti / Right Button by ninjamic
...frsky horus x12s menu poti / right button by ninjamic
thingiverse
menu-poti for frsky horus x12s
printed in pla 0,10 layer high
thingiverse
free
EBS New Module Poti by wolle57
...ning terminals. these junctions are not detailed on the picture.
hope, you like it. i'll continue the ebs more or less daily.
thingiverse
free
Knobs for Potis or Rotaryencoders (6mm Shaft) by PhilCraft
...knobs for potis or rotaryencoders (6mm shaft) by philcraft
thingiverse
diverse knobs for a future project.
thingiverse
free
Drehknopf Poti 6mm Achse m. Bohrung für 4mm Gewinde by drachental
...drehknopf poti 6mm achse m. bohrung für 4mm gewinde by drachental
thingiverse
drehknopf für 6mm achse von potis
Fixa
3dfindit
free
Trelica fixa
...trelica fixa
3dfind.it
catalog: de lazzari
thingiverse
free
IKEA FIXA gear motor by geobruce
...ikea fixa gear motor by geobruce
thingiverse
this is a 3d model of the motor used in the ikea fixa screwdriver
thingiverse
free
IKEA FIXA motor holder by geobruce
...ikea fixa motor holder by geobruce
thingiverse
this is a motor holder for the motor and gearbox of the ikea fixa screwdriver
sketchfab
$5
IKEA Fixa kitchen wall protection (Printable)
...p/fixa-falvedo-szegely-szuerke-40246038/ - ikea fixa kitchen wall protection (printable) - buy royalty free 3d model by svandor82
thingiverse
free
Short Hypercube leg for IKEA FIXA by kusha
...ure)
wider hole in the leg axis to fit ikea fixa foot protector ($2)
extended holes for 2020 profile screws to fit into the model
thingiverse
free
IKEA FIXA motor mount by DaRyde
...s robotic projects. the motor mount have room for two additional bearings type 61800 10x19x5mm (placement shown in the pictures).
thingiverse
free
IKEA FIXA robot lawn mover wheel by DaRyde
...mounted on a ikea fixa motor/gearbox (ikea article.no: 002.142.04). there is also a suitable motor mount in my things collection.
thingiverse
free
IKEA Fixa level box by balassy
...g and glue it into the base.
you need 4 pcs 5×2 mm (diameter 5 mm, thickness 2 mm) magnets to keep the base and the lid together.
thingiverse
free
Fitting Cyllinder for Ikea Morik charger and Fixa drill set by ScotchBunny
...eaves about 5 mm space all around the charger.
i made the fitting piece to compensate for the blade radius and lower the charger.
thingiverse
free
IKEA Fixa Hole Saw Thin Grommets by balassy
...s, you may try to resize the models in your slicer, or open the attached source file in fusion 360 and change the extrude length.