25 brodo78 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
FM800 RC Receiver Mount by Brodo78
...fm800 rc receiver mount by brodo78
thingiverse
this is a mount for the fm800 s.bus/fasst diversity receiver.
thingiverse
free
Intellicharger i2 stand/holder/bracket by Brodo78
...intellicharger i2 stand/holder/bracket by brodo78
thingiverse
wall mount bracket for an intellicharger i2.
thingiverse
free
CubeCell GPS Antenna Clip by Brodo78
...rse
this is a trivial clip so the original heltec lora antenna can be used with softrf's case rather than an sma patch lead.
thingiverse
free
Quadplane Arm Wing Mount by Brodo78
... make a quadplane.
it has a large base to distribute the load over a greater surface area.
the bolt holes are made for ~m3 bolts.
thingiverse
free
Tortoise Shell (Photogrammetry Model) by Brodo78
...-models/tortoise-shell-ae80c59579474d6991691c5500538f80
the stl includes supports, in about the only orientation that made sense.
thingiverse
free
MaxBotix MaxSonar Case by Brodo78
...so board can fit inside more easily.
increase cable hole size so i2c connector can fit through.
increase wall thickness slightly.
thingiverse
free
M3 screw terminals power distribution by Brodo78
...be printed from conductive filament if you want isolation between the different terminals.
print on the side, no supports needed.
thingiverse
free
GoPro H3-3D Gimbal Strap with Payload Hook by Brodo78
...ix includes a small cutout for the gopro buttons and has a hook, so that when you tilt the gimbal down a payload can be released.
thingiverse
free
Yet Another Drone Landing Leg F450/F550 by Brodo78
... ties or with ~m3 bolts using the top plate provided.
the small recesses on one end are to facilitate removal from the print bed.
thingiverse
free
ImmersionRC FPV Transmitter Mount for FlameWheel Arm by Brodo78
...heel f450/f550 arm hub.
there's a few holes for increased airflow, holes for two small cable ties, and a gusset for strength.
thingiverse
free
FlameWheel F550 Cross-Arm Mounting Truss by Brodo78
...2-based gimbal, but hopefully the slots offer some flexibility.
you could attach it to the arms using either bolts or cable ties.
thingiverse
free
Slide-In GoPro Mount for Storm32 Gimbal by Brodo78
...g photos. i just used some silicone to attach the mount to the blade.
print it with the solid end down, no supports are required.
thingiverse
free
Universal Electric Power Window Gear Replacement by Brodo78
...les.
edit: i later found this thing which looks like it could be for the same assembly: https://www.thingiverse.com/thing:3692909
thingiverse
free
T-motor to DJI style propeller adapter by Brodo78
...how it goes for you.
it will print with no supports.
you will need to expand the centre hole on the propeller using an ~m6 drill.
thingiverse
free
Reinforced FlameWheel Arm/Landing Leg by Brodo78
...t; blades. this is just snowboarder1337's stl with the middle bit chopped out and the two parts stitched together in blender.
thingiverse
free
DJI F550 Drone Arm by Brodo78
...he print bed.
i've been using these with m3 bolts at the drone end mount and small screws on the secondary holes at that end.
thingiverse
free
FlameWheel F550 Extended Arm for 11" Propellers by Brodo78
...ure prints with solid columns from top to bottom rather than just containing infill. these can also be used for attaching things.
thingiverse
free
DJI Phantom Battery Holder by Brodo78
...fully it can withstand some good crashes!
the battery clips/unclips well - better than on the dji original, at least on my drone.
thingiverse
free
Dog Slow Feeder Bowl Insert by Brodo78
...9;t bear to watch the torment of your dog struggling to get the last few pieces of food.
print from something food-safe like pla.
thingiverse
free
Print in Place Customizable Box With Latches by Brodo78
...lid and the rest of the box should be generated/printed separately. the latches do need some supports, as per the attached image.
thingiverse
free
GoPro Mount for RC Plane Vertical Stabilizer by Brodo78
...ther thicknesses too.
of course the mount might be useful for other applications beyond mounting on the tail of a model airplane!
thingiverse
free
DJI F550 Top Plate With Easy Internal Access by Brodo78
...conductive) and lined it with copper tape just to help decrease the rfi/emi noise environment for the gps and rc antennas on top.
thingiverse
free
DJI Phantom 2 Airframe Reborn by Brodo78
...o the design as i clock up more flight time with it. i also still need to add an hd-3d gimbal mounting point and the prop guards.
thingiverse
free
Carbon Fibre Landing Leg/Skid Bits (Quanum 800) by Brodo78
...l quanum 800 product, you could equally use these designs with any 25mm/16mm carbon fibre tubes.
no supports needed for printing.
thingiverse
free
Cusomisable LiPo Battery Box/Enclosure/Mount for Drone etc by Brodo78
...s by swapping your width and height parameters.
the mounting bolt holes, if you select those options, are optimised for m3 bolts.