Thingiverse
The Double D: Derringer Crossbow Pistol by mechanic403
by Thingiverse
Last crawled date: 3 years, 4 months ago
The Double D is a compact crossbow pistol which fires two arrows at the same time. It can be pre loaded with the two arrows ready in its chamber and can then be cocked quickly and fired. It has a break-action and is breech loaded.
Required Parts:
M4 Screws and nuts: 2x M4x20, 1x M4x12, 1x M4x10
M3 Screws and nuts: 3x M3x12, 1x M3x20
Small Rubber Bands
Large Rubber Bands
3x Magnets 5mm Diameter x 3mm cylindrical neodymium
Super Glue
If you dont have the magnets, print the _NonMagnetic part variants which use a different Barrel Latch mechanism.
UPDATE: Added engraved parts
Assembly Guide
Grip and Receiver
Gather the Grip_Left, Grip_Right, GripScale_Left, GripScale_Right, GripReceiverSidePlate_Left, GripReceiverSidePlate_Right, the Receiver, 2 M4x20 screws, 3 M3x12, an M3x20 and the small rubber band
Take one of the grip halves and the corresponding ReceiverSidePlate and feed the M3x20 screw into the hole in the ReceiverSidePlate and then through the Grip half's hole for the trigger. Place the trigger onto the screw through the other side of the Grip so it sits in the cut out chamber. Loop the rubber band around the trigger in the small notch and pull the band upwards so that it sits in the small channel in the top of the Grip. Then connect the other grip half with the screw and place the other ReceiverSidePlate on top, securing with the end of the screw and a hex nut. Loop the rubber band around the small hook on the grip and make sure that it has good tension, the stronger the better
Screw the GripScales onto the grip with the M4x20 screws and nuts.
Next, place the flat face of the Receiver against the front of the Grip and secure with two M3x12 screws. Make sure the screw heads are fully inserted into the Receiver so that the front surface is flat.
Check the images at the bottom for help assembling the latch
Take the BarrelLockLever halves and glue them together. Insert a magnet into the small hole in the thumb rest of the lever and glue into place. Place the other two magnets, stacked, in the small hole on the top of the Grip and ensure they have the opposite polarity as the one in the lever so that they repel. Screw the lever into the Receiver's hinge with the M3x12 screw. You should be able to press down the lever and have it spring back.
Alternatively, if youve printed the NonMagnetic parts, screw the M3x12 through the LockLever_NonMagnetic's top hole, then apply a bit of glue to the end of the screw once it comes out the other side. Screw this into the hole in the top of the Grip (the NonMagnetic version of the grip has a smaller, deeper hole than the regular version). Ensure the LockLever can rotate freely, yet is tight against the top face of the grip and doesnt wobble.
Barrel
Gather the Barrel, two ArrowRetentionTabs, BarrelLockLatch, BarrelHinge and BarrelBreechPlate, along with an M4x12 screw.
Insert the BarrelHinge into the rectangular slot on the bottom of the Barrel, closest to the breech, and glue in place. Insert the BarrelLockLatch into the small square slot on the top of the Barrel and glue into place. Ensure the angled slope faces towards the breech end. If using the NonMagnetic latch, ensure the longer thinner end is pointing towards the breech. Insert each ArrowRetentionTab into the long open rectangular slots on the barrel, glue the flat squarish face of the tab onto the small indent in the slot. The raised portion of the tab should point inward to the center of the barrel. These tabs keep the arrows in place when theyre inserted and prevent them from sliding out.
Sled
Gather all of the parts from the Sled_Assembly and get a short peice of filament (1.75mm). Check the images for the names of each part.
Glue the two rectangular peices together such that the two holes are aligned. Insert the two SledTabs into the slot in the SledMechanism and feed a peice of the filament through each hole such that the tabs can rotate. Use a knife to cut the filament so it is flush with each side of the SledMechanism.
Insert the SledGrip onto the SledMechanism via the slots and glue together. Insert the SledActuator into the thin slot on the rear of the SledMechanism. Ensure that it can slide back and forth and push up the two SledTabs so that they extend outwards. Finally, glue the SledTriggerHook onto the back of the SledMechaism so that it contains the SledActuator. Make sure to glue this very strongly as it holds all of the tension in the Derringer.
You can now insert the assembled sled into the barrel with the hook end facing towards the breech. It should slide freely along the channel in the barrel. You should be able to push arrows into the barrel via the breech and have them push the SledTabs downward and thus move the actuator back.
Final Assembly
With the Sled inserted into the barrel channel, place the BarrelBreechPlate onto the breech end of the barrel with the two small pegs inserted into the small holes on the Barrel and glue into place.
Connect the BarrelHinge to the Receiver with an M4x12 screw so that it can rotate freely. You should be able to rotate the barrel so that its flush with the Receiver and have the LockLever catch it and hold it in place.
Take the BarrelFrontBandSupport, or MuzzleBowArms / MuzzleBowArms_Compact and place it on the muzzle of the barrel. Use an M4x10 screw to secure it to the barrel. Loop a strong rubber band through the holes in the Sled such that each end of the band is connected to one of the sides of the Sled. The band should then be pulled over the FrontBandSupport and rest in its curved channel.
Alternatively, print the MuzzleBowArms part and use instead. Its a bit less streamlined but itll allow for more power!
Congrats! Youre done :) Just print two (or more) arrows and glue the halves together.
Loading and Firing
To load, first press down on the LockLever to open the barrel breech. Push the arrows into the shafts in the barrel. You should feel the SledTabs click down. The rear end of the arrows should be pressed in a small way so that theyre a bit past the face of the breech plate. Close the barrel so the LockLever locks it in place.
Now just pull the sled back all the way. It should click into place, pushing the SledActuator forward, rotating the SledTabs outward so that they can push against the rear end of the arrows when fired. Aim the Derringer and pull the trigger to fire both arrows at once! You can also optionally load a single arrow if you desire. Enjoy!
Required Parts:
M4 Screws and nuts: 2x M4x20, 1x M4x12, 1x M4x10
M3 Screws and nuts: 3x M3x12, 1x M3x20
Small Rubber Bands
Large Rubber Bands
3x Magnets 5mm Diameter x 3mm cylindrical neodymium
Super Glue
If you dont have the magnets, print the _NonMagnetic part variants which use a different Barrel Latch mechanism.
UPDATE: Added engraved parts
Assembly Guide
Grip and Receiver
Gather the Grip_Left, Grip_Right, GripScale_Left, GripScale_Right, GripReceiverSidePlate_Left, GripReceiverSidePlate_Right, the Receiver, 2 M4x20 screws, 3 M3x12, an M3x20 and the small rubber band
Take one of the grip halves and the corresponding ReceiverSidePlate and feed the M3x20 screw into the hole in the ReceiverSidePlate and then through the Grip half's hole for the trigger. Place the trigger onto the screw through the other side of the Grip so it sits in the cut out chamber. Loop the rubber band around the trigger in the small notch and pull the band upwards so that it sits in the small channel in the top of the Grip. Then connect the other grip half with the screw and place the other ReceiverSidePlate on top, securing with the end of the screw and a hex nut. Loop the rubber band around the small hook on the grip and make sure that it has good tension, the stronger the better
Screw the GripScales onto the grip with the M4x20 screws and nuts.
Next, place the flat face of the Receiver against the front of the Grip and secure with two M3x12 screws. Make sure the screw heads are fully inserted into the Receiver so that the front surface is flat.
Check the images at the bottom for help assembling the latch
Take the BarrelLockLever halves and glue them together. Insert a magnet into the small hole in the thumb rest of the lever and glue into place. Place the other two magnets, stacked, in the small hole on the top of the Grip and ensure they have the opposite polarity as the one in the lever so that they repel. Screw the lever into the Receiver's hinge with the M3x12 screw. You should be able to press down the lever and have it spring back.
Alternatively, if youve printed the NonMagnetic parts, screw the M3x12 through the LockLever_NonMagnetic's top hole, then apply a bit of glue to the end of the screw once it comes out the other side. Screw this into the hole in the top of the Grip (the NonMagnetic version of the grip has a smaller, deeper hole than the regular version). Ensure the LockLever can rotate freely, yet is tight against the top face of the grip and doesnt wobble.
Barrel
Gather the Barrel, two ArrowRetentionTabs, BarrelLockLatch, BarrelHinge and BarrelBreechPlate, along with an M4x12 screw.
Insert the BarrelHinge into the rectangular slot on the bottom of the Barrel, closest to the breech, and glue in place. Insert the BarrelLockLatch into the small square slot on the top of the Barrel and glue into place. Ensure the angled slope faces towards the breech end. If using the NonMagnetic latch, ensure the longer thinner end is pointing towards the breech. Insert each ArrowRetentionTab into the long open rectangular slots on the barrel, glue the flat squarish face of the tab onto the small indent in the slot. The raised portion of the tab should point inward to the center of the barrel. These tabs keep the arrows in place when theyre inserted and prevent them from sliding out.
Sled
Gather all of the parts from the Sled_Assembly and get a short peice of filament (1.75mm). Check the images for the names of each part.
Glue the two rectangular peices together such that the two holes are aligned. Insert the two SledTabs into the slot in the SledMechanism and feed a peice of the filament through each hole such that the tabs can rotate. Use a knife to cut the filament so it is flush with each side of the SledMechanism.
Insert the SledGrip onto the SledMechanism via the slots and glue together. Insert the SledActuator into the thin slot on the rear of the SledMechanism. Ensure that it can slide back and forth and push up the two SledTabs so that they extend outwards. Finally, glue the SledTriggerHook onto the back of the SledMechaism so that it contains the SledActuator. Make sure to glue this very strongly as it holds all of the tension in the Derringer.
You can now insert the assembled sled into the barrel with the hook end facing towards the breech. It should slide freely along the channel in the barrel. You should be able to push arrows into the barrel via the breech and have them push the SledTabs downward and thus move the actuator back.
Final Assembly
With the Sled inserted into the barrel channel, place the BarrelBreechPlate onto the breech end of the barrel with the two small pegs inserted into the small holes on the Barrel and glue into place.
Connect the BarrelHinge to the Receiver with an M4x12 screw so that it can rotate freely. You should be able to rotate the barrel so that its flush with the Receiver and have the LockLever catch it and hold it in place.
Take the BarrelFrontBandSupport, or MuzzleBowArms / MuzzleBowArms_Compact and place it on the muzzle of the barrel. Use an M4x10 screw to secure it to the barrel. Loop a strong rubber band through the holes in the Sled such that each end of the band is connected to one of the sides of the Sled. The band should then be pulled over the FrontBandSupport and rest in its curved channel.
Alternatively, print the MuzzleBowArms part and use instead. Its a bit less streamlined but itll allow for more power!
Congrats! Youre done :) Just print two (or more) arrows and glue the halves together.
Loading and Firing
To load, first press down on the LockLever to open the barrel breech. Push the arrows into the shafts in the barrel. You should feel the SledTabs click down. The rear end of the arrows should be pressed in a small way so that theyre a bit past the face of the breech plate. Close the barrel so the LockLever locks it in place.
Now just pull the sled back all the way. It should click into place, pushing the SledActuator forward, rotating the SledTabs outward so that they can push against the rear end of the arrows when fired. Aim the Derringer and pull the trigger to fire both arrows at once! You can also optionally load a single arrow if you desire. Enjoy!
Similar models
thingiverse
free
Gravitrax Compatible Ballista by mechanic403
...nel of the base. once a ball is rolled into the rear end, it should release the trigger and send the ball in the channel flying!
grabcad
free
DOUBLE BARREL SWIVEL BREECH DERRINGER
...double barrel swivel breech derringer
grabcad
double barrel swivel breech derringer
thingiverse
free
Bolt Action Air Rifle with Shell Ejection (CO2 Powered) by mechanic403
...n up the fit.
you can now insert a co2 cartridge into the handle of the pump and load up some shells and magazines and test fire!
thingiverse
free
Single Action CO2 Airgun Revolver by mechanic403
...was inspired by the webley revolver and has a similar form factor. disclaimer: by downloading these files, you agree...
thingiverse
free
Rubber Band Cannon (threaded barrel) by nakeib
...nsert plate with a stick and put the ball on a stick end. to prevent ball sliding off, just flatten a stick end with a hot knife.
thingiverse
free
Rubber band gun - easy spring insertion by SapoLAB
...by sapolab
thingiverse
remix that adds a hole to insert the spring after printing and a cap to fix the spring in place with glue
thingiverse
free
Floats and Boats Expansion Pack by Supergirl2000
... attached with string to the balloon clip or corresponding connectors. an additional challenge could be a water bottle submarine.
thingiverse
free
Extended Barrel Rubber Band Gun by Forgedinplastic3d
...extended barrel rubber band gun by forgedinplastic3d
thingiverse
a remix of a rubber band gun with extended barrel and grips.
thingiverse
free
Rubber Band Bow by ShakinBakin
...r clip at both ends when inserted, cut ends to length
found rolled paper with tape on end for added weight works best for arrows.
thingiverse
free
Rubber Band Powered Toy Cannon by unistrut
... hammer, make sure the rubber band on the sear is pulling it into position and not getting caught up in the rest of the workings.
Mechanic403
thingiverse
free
Gravitrax Compatible Trap Door Tile by mechanic403
...lever can then be snapped into place in the trapdoorinsert. finally, insert the whole assembly into oostmeijer's basic tile.
thingiverse
free
Gravitrax Compatible Ballista by mechanic403
...nel of the base. once a ball is rolled into the rear end, it should release the trigger and send the ball in the channel flying!
thingiverse
free
Lament Configuration [Minimalist Version] by mechanic403
...the surface. itll stick well and wont leave any discolored residue.
update: fixed some small gaps in the connector bits on facec
thingiverse
free
Spongebob and Patrick Earrings by mechanic403
... patrick, i printed in whatever color, sanded smooth and then painted with pink nailpolish and finished with a clear coat.
enjoy!
thingiverse
free
Bolt Action Air Rifle with Shell Ejection (CO2 Powered) by mechanic403
...n up the fit.
you can now insert a co2 cartridge into the handle of the pump and load up some shells and magazines and test fire!
thingiverse
free
[Star Wars] Batuuan Spira Credits by mechanic403
...t an exact replica but pretty close. the back side is blank. you can print two and glue them together for a double sided model.
thingiverse
free
Gravitrax - Cannon by TJJPrusa
...thingiverse gravitrax compatible cannon. based on the design of mechanic403 https://www.thingiverse.com/thing:4616717 logo use is optional (can be hammered in...
thingiverse
free
Designer Six Sided Dice by mechanic403
...er printing, i painted each pip with nail polish. after fully dried, i wet sanded each face with 220 grit to clean up the paint.
thingiverse
free
Circuit Six Sided Dice by mechanic403
...ve included two variations: one with thin lines connecting the pips and one where the lines are the same width as the pips
enjoy!
Derringer
humster3d
$50
3D model of COP .357 Derringer
... detailed 3d model of cop .357 derringer in various file formats. all our 3d models were created maximally close to the original.
humster3d
$50
3D model of Remington 1866 Derringer
...led 3d model of remington 1866 derringer in various file formats. all our 3d models were created maximally close to the original.
3d_export
free
Download free REPRRINGER v2 PENTAGUN 3d printable gun 3D Model
...reprringer v2 pentagun 3d printable gun 3d model 3dexport derringer pepperbox gun pistol firearm reprringer pentagun printable 3d print...
3d_export
free
Download free REPRRINGER 3d printable gun 3D Model
...download free reprringer 3d printable gun 3d model 3dexport derringer pepperbox gun pistol firearm reprringer printable 3d print reprringer...
3d_export
free
Download free REPRRINGER v3 HEXEN 3d printable gun 3D Model
...reprringer v3 hexen 3d printable gun 3d model 3dexport derringer pepperbox gun pistol firearm reprringer hexen printable 3d print...
turbosquid
$4
Remington Model 95 Derringer
... free 3d model remington model 95 for download as obj and fbx on turbosquid: 3d models for games, architecture, videos. (1701106)
turbosquid
$5
derringer
... available on turbo squid, the world's leading provider of digital 3d models for visualization, films, television, and games.
turbosquid
$10
Derringer Philadelphia
...royalty free 3d model derringer philadelphia for download as on turbosquid: 3d models for games, architecture, videos. (1622641)
thingiverse
free
Nerf Rainbow Derringer by shoelesshistorian
...inbowrevolvercylinderbase -> smallrainbowrevolverfront. you'll want craft foam to seal between the cylinder and the front.
Crossbow
3d_export
$29
Low Poly Medieval Weapons 3D Model
...3d model 3dexport medieval weapons scythe hatchet sword knife crossbow halbert spear sabre scabbard lowpoly realtime low poly medieval...
3d_ocean
$29
Low Poly Skeleton Archer
...poly skeleton archer 3docean 3d model archer bitgem bolt crossbow enemy game hand painted low poly monster quiver skeleton...
3d_ocean
$15
Crossbow
...listic weapon
3d model of crossbow .objects are grouped.rendering scene with materials are included and detailed, with all files.
3d_ocean
$89
Low Poly Skeleton Crew 02
...poly skeleton crew 02 3docean archer bitgem boss brute crossbow grunt hand painted king low poly mage magician skeleton...
3d_export
$15
High Poly Sniper Crossbow 3D Model
...ope rifle trigger
high poly sniper crossbow 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl sisli01 102952 3dexport
3d_export
$10
Crossbow 3D Model
...odel
3dexport
crossbow solidworks
crossbow 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl mykhailo 113409 3dexport
cg_studio
$25
Hand Crossbow3d model
...dival hunting
.3dm .3ds .c4d .max .obj - hand crossbow 3d model, royalty free license available, instant download after purchase.
3ddd
$1
CrossBow
...crossbow
3ddd
арбалет
арбалет от фирмы barrnet
cg_studio
$29
low poly crossbow3d model
...fletching
.obj .max .fbx .c4d .3ds - low poly crossbow 3d model, royalty free license available, instant download after purchase.
3d_ocean
$7
Medieval Crossbow
...sm to your rendering projects. detailed enough for close-up renders. comes with detailed color map textures. originally modell...
Pistol
3d_export
$35
Makarov 9mm pistol 3D Model
...makarov 9mm pistol 3d model
3dexport
gun weapon pistol 9-mm 9mm makarov
makarov 9mm pistol 3d model lubomir88 22086 3dexport
3d_export
$22
Quad Shotgun 3D Model
...model 3dexport quad shotgun shot gun sniper machine gatling pistol handgun weapon game ready gameready quad shotgun 3d model...
3d_export
$20
Walther WA 2000 3D Model
...2000 wa2000 ww sniper rifle machine gatling submachine gun pistol handgun weapon game ready gameready walther wa 2000 3d...
3d_ocean
$17
Smith & Wesson Model 1 Whith Short .22
...whith short .22 3docean .22 antiques bullet. metal old pistol shell silver smith and wesson model one the bad...
3d_ocean
$16
Shotgun
...3d shotgun game weapon gun guns low poly shotgun pistol rifel weapon low poly shotgun v-ray rendering high quality...
3d_ocean
$5
Raygun - Alien Blast Pistol
...iple format: -fbx -3ds -obj -max all the preview image was rendered in v-ray with v-ray toon effect. you can easily change the...
3d_export
$40
9mm handgun 3D Model
...9mm handgun 3d model 3dexport weapon pistol gun handgun 9mm holster silencer 9mm handgun 3d model...
3d_ocean
$15
Five-Seven
...five-seven 3docean bullet calibre five game gun military model pistol ready seven war weapon five-seven calibre 5.7×28mm pistol lowpoly...
archive3d
free
Pistol 3D Model
...hive3d
pistol fire-arms gun
pistol n141214 - 3d model (*.gsm+*.3ds+*.max) for 3d visualization.
archive3d
free
Pistol 3D Model
...fire-arms pistol shooter
pistol n211008 - 3d model (*.gsm+*.3ds) for interior 3d visualization.
Double
3ddd
$1
IKEA Svartsjon Double hook
...ikea svartsjon double hook
3ddd
ikea , крючок
двойной крючок ikea
3ddd
$1
MERCANTILE DOUBLE VANITY SINK
...а , бра , зеркало
mercantile double vanity sink
3ddd
$1
Kohler Triton® Shelf-back double wristblade lever handle sink faucet with loose-key stops
... смеситель
медицинский (хирургический) смеситель
height 8-7/16"
length 7-5/8"
width 8"
k-7308-5a-cp
3ddd
$1
ClassiCon Double-X
...classicon double-x
3ddd
classicon
classicon double-x modern table
3ddd
$1
Vespa
...end table crafted from solid and veneered mahogany with double 'v' detailing. (shown in java cafe varnish/renaissance gold) w65...
3ddd
$1
Double palm trees in a pot
...uble palm trees in a pot
3ddd
пальма , горшок
double palm trees in a pot with brass foot
3ddd
$1
Generic Windows
...generic windows 3ddd окно generic, double glass...
3d_ocean
$25
Container shipping House double floor
...l is fully textured with all applied materials: - textures formats: tif (x4) - textures size: x1024 (x1), x2048 (x3) - materia...
3d_ocean
$5
Double Sofa
...double sofa
3docean
double sofa made by fabric, wood & ss leg
3ddd
$1
Leather double bed
...leather double bed
3ddd
leather double bed, dimension: 180x210 cm