Thingiverse
Rc cars shelf by lezacy_bykiem
by Thingiverse
Last crawled date: 3 years, 1 month ago
Mine was done this way:
Cut OSB-3 board in proportion: 70 to 30 cm
Use any generic shelf support to mount a to szelf (30 cm piece) on top
Put m10x30 nut into "wieszak" cutout and than plug hole with printed plug (part of "wieszak". You can use glue to secure parts if you need. (i did).
Cut Aluminium bar to size: 60 cm
Put plastic parts in bellow order on the rod:
wspornik (on the side)
wieszak (this one is movable)
wspornik (put it on the middle - it's optional but recommended for long hooks)
wieszak (this one is movable)
wspornik (on the opposite side of 1st one)
Screw whole set of "wspornik" onto the board
Repeat for all of the shelf's
Cut threaded rod into desired pieces, 1 for each of the "wieszak"
Insert and cut heat shrinks on the thread rod pieces so 40mm of thread is not protected.
Shrink it with gaslight or hot air on the ends of shrink tube so it would be secured, this is your hook
Screw hook into m10 nut inside of "wieszak", note that if you screw it into the end it would lock itself onto the alu bar, so it would not be moving.
Notes:
If holes for aluminum bar are to tight heat them with hot air or similar and push bar through.
Bill of materials for 4 shelfs:
OSB-3 Board 60x100 cm 10 mm thick x 1 pcs
Wood Screws 4x35 mm x 36 pcs
Aluminum bars/pipe 15x60cm x 4 pcs(1 for each shelf)
M10 threaded bar x 2-4 pcs (depends on how deep hooks are going to be)
M10 x 30 mm nuts x 8 pcs.
Your fav glue for plastic parts
Heat shrinking tubes 12mm for protecting thread on hooks 2-4 pcs
wspornik.stl x 12 pcs
wieszak_rc.stl x 8 pcs
Any king of standard shelf mounts if you like shelf on the top (as on pic)
Cut OSB-3 board in proportion: 70 to 30 cm
Use any generic shelf support to mount a to szelf (30 cm piece) on top
Put m10x30 nut into "wieszak" cutout and than plug hole with printed plug (part of "wieszak". You can use glue to secure parts if you need. (i did).
Cut Aluminium bar to size: 60 cm
Put plastic parts in bellow order on the rod:
wspornik (on the side)
wieszak (this one is movable)
wspornik (put it on the middle - it's optional but recommended for long hooks)
wieszak (this one is movable)
wspornik (on the opposite side of 1st one)
Screw whole set of "wspornik" onto the board
Repeat for all of the shelf's
Cut threaded rod into desired pieces, 1 for each of the "wieszak"
Insert and cut heat shrinks on the thread rod pieces so 40mm of thread is not protected.
Shrink it with gaslight or hot air on the ends of shrink tube so it would be secured, this is your hook
Screw hook into m10 nut inside of "wieszak", note that if you screw it into the end it would lock itself onto the alu bar, so it would not be moving.
Notes:
If holes for aluminum bar are to tight heat them with hot air or similar and push bar through.
Bill of materials for 4 shelfs:
OSB-3 Board 60x100 cm 10 mm thick x 1 pcs
Wood Screws 4x35 mm x 36 pcs
Aluminum bars/pipe 15x60cm x 4 pcs(1 for each shelf)
M10 threaded bar x 2-4 pcs (depends on how deep hooks are going to be)
M10 x 30 mm nuts x 8 pcs.
Your fav glue for plastic parts
Heat shrinking tubes 12mm for protecting thread on hooks 2-4 pcs
wspornik.stl x 12 pcs
wieszak_rc.stl x 8 pcs
Any king of standard shelf mounts if you like shelf on the top (as on pic)
Similar models
thingiverse
free
Heat-shrink cutting fixture 3/4" by jimlee
...ink cutting fixture 3/4" by jimlee
thingiverse
i cut a lot of 3/16 heat-shrink into 3/4" pieces. this makes it easier.
thingiverse
free
Hühner "Stagenhalter" (Vogelmilbe) by Shedox12
...ot;stagenhalter" (vogelmilbe) by shedox12
thingiverse
you need a 15cm long m10 threaded rod, 4 washer & 4
thread nuts.
thingiverse
free
prusa i3 rework 1.5 alu frame brace for M10 threaded road by hygy
... long one
you need 4 pieces of m4x23mm screw + nut + washer
2 pieces of 36cm long m10 threaded rod + 8 pieces of m10 nut + washer
thingiverse
free
M10 threaded rod connector by 4n4rchy73c7
...signed this for a diagonal support of my printers frame.
+++ update 2018-07-15 +++
minor changes to make it printable more easily
thingiverse
free
Adjustable Monitor Wall Mount by blankdesign
...to mount a benq el2870u monitor but should also work for any monitor that has the same screw spacing on the back (100mm x 98mm).
thingiverse
free
CR-10s Pro Frame Brace V2
...e bottom mount:
1) there are 2 screws at the corner, remove it first.
2) install the bottom mount.
3) put those 2 screws back in.
thingiverse
free
350W wheelchair adapter by checkerz4456
...ded rods, 2 (6" x 1/4") threaded rods, 12 bolts for the rods, two 2" wall screws, and two 3 1/2" wall screws.
grabcad
free
F1 steering wheel - 3D printable
...e 30x12 (3mm dia, 12mm length)
use screws with wide heads (integrated disc) or use a washer if you have screws with small heads.
3dwarehouse
free
LAG Screw - M10
...lag screw - m10
3dwarehouse
lag screw - m10. stainless steel, coach screw x threaded rod, sck drive
thingiverse
free
HC Maker 7 LCD case by scottypitcher
... rear of the base and screwing them up tight.
fit the knob back to the control shaft on the top cover and fix in place.
---fin---
Rc
3ddd
$1
Roberto Cavalli RC 13003b
...roberto cavalli rc 13003b
3ddd
roberto cavalli
обои roberto cavalli и industrie emiliana parati spa, rc 13003b
3d_ocean
$25
RC F1
...rc f1
3docean
auto car control f1 formula race rc remote speed
remote control f1 car
3d_ocean
$19
Braid 4 RC wheel + tyre
...heel (tire + rim + brake disc + caliper) has 30.700 polygons (not smoothed). i didn’t applied (collapsed) a smooth modifier on...
3d_ocean
$89
Lexus RC 2014
...y, in real units of measurement, qualitatively and maximally close to the original. model formats: - *.max (3ds max 2008 scanl...
3ddd
$1
LG G2 smartphone
...3g (hspa+42mbps / hspa+21mbps) lte (svlte, csfb, ca, volte, rc, mimo) dimensions ** 138.5 (l) x 70.9 (w) x...
3ddd
$1
Робот-пылесос "Karcher RC 3000"
... робот , пылесос
робот-пылесос "karcher rc 3000"
3ddd
$1
Kuppersberg RC 699 ANT BRONZE
...kuppersberg rc 699 ant bronze
3ddd
kuppersberg , духовой шкаф
электрический духовой шкаф
3ddd
$1
Klipsch
...klipsch rf-83 floorstanding speaker, rt-12d subwoofer, rs-62 surround speaker, rc64 center speaker модели детальные, по размерам, с текстурами. 148370...
cg_studio
$99
RC buggy model3d model
...o
.3ds .c4d .fbx .lwo .max .obj .xsi - rc buggy model 3d model, royalty free license available, instant download after purchase.
3ddd
$1
BOSS RC-2 Loop Station
...rc-2 loop station
3ddd
гитарный эффект boss rc-2
педаль позволяет записать аудио, наложить петли друг на друга, закольцевать их.
Shelf
3d_export
$19
Celtic Three Drawer Storage Shelf 3D Model
...d section southern enterprises furniture locker chest drawers
celtic three drawer storage shelf 3d model humster3d 72046 3dexport
3d_export
$12
Shelf MAX 2011 3D Model
...ookshelf modern wood art colours furniture livingroom house decoration
shelf max 2011 3d model motionmediaworkshop 70255 3dexport
3d_export
$19
Convexshapes Kitchen Decorations Wine stand 3D Model
...3d model 3dexport kitchen stuff decorations wine cellar stand shelf rack bottle convex 3ds max cinema c4d vray mentalray...
3d_export
$19
Convexshapes Kitchen Decorations Wine shelf 3D Model
...ttle convex 3ds max cinema c4d vray mentalray
convexshapes kitchen decorations wine shelf 3d model convexshapes 69762 3dexport
3d_export
$27
Bathroom shelf 3D Model
...
3dexport
bath storage corner decoration shelf ronnskar shower bathroom hygiene
bathroom shelf 3d model livevertex 77898 3dexport
3d_export
$34
Computer desk 3D Model
...computer desk table furniture interior office design home room shelf box wood high poly 3d model computer desk 3d...
3ddd
$1
Display Cabinet FS
...display cabinet fs 3ddd book shelf ...
3ddd
$1
Kohler Triton® Shelf-back double wristblade lever handle sink faucet with loose-key stops
... смеситель
медицинский (хирургический) смеситель
height 8-7/16"
length 7-5/8"
width 8"
k-7308-5a-cp
3ddd
$1
Decorative shelf -3
... живопись , картина
decorative shelf ,,, saved max 2015, 2012, fbx
3ddd
$1
Cosmo Ice Bear Shelf
... bear
полка ice bear shelf
размеры: 100х160х45 cm.
70 000 polygons, turbosooth iteration = 2
Cars
3d_export
$99
Peugeot Boxer Minibus 2014 3D Model
...2014 3d model 3dexport peugeot boxer minibus 2014 car cars light vehicle van france cargo passenger minibus bus commercial...
3d_export
$99
Jaguar XK150 S Fastback 3D Model
...port coupe fastback hartin 3d model old british 1957 1958 1960 vehicle
jaguar xk150 s fastback 3d model desmonster 90169 3dexport
3d_export
$99
Mercedes Benz A180 Eco 2015 3D Model
...014 car 2015 2016 compact mercedes-benz germany eco hatchback 2017 a180
mercedes benz a180 eco 2015 3d model squir 90623 3dexport
3d_export
$7
Rim 3D Model
...rim 3d model
3dexport
rim wheel car keychains
rim 3d model dosoriofp78431 90998 3dexport
3d_export
$99
Citroen Relay Van L1H1 2015 3D Model
...2015 3d model 3dexport citroen relay van l1h1 car cars light vehicle van france cargo mini bus commercial transport...
3d_export
$109
BMW 7 e38 1994 2001 3D Model
...m german sloon seven detailed realistic mental ray vray transporter 750i
bmw 7 e38 1994 2001 3d model fisherman3d 71988 3dexport
3d_export
$10
Cars Departement City 3D Model
...e departement city streeth traffic police white light 3d fire school bus
cars departement city 3d model nolgraphic 72342 3dexport
3d_export
$99
Lancia Stratos std mat 3D Model
...photorealistic speed people drive championship italy italia italian munari
lancia stratos std mat 3d model fabelar 72528 3dexport
3d_export
$5
Car rim 3D Model
...car rim 3d model
3dexport
car rim 3d model hitman47 72546 3dexport
3d_export
$25
BMW 502 3D Model
...bmw 502 3d model
3dexport
bmw luxury old car auto 502 automobile
bmw 502 3d model septimussignus 73907 3dexport