Thingiverse
MPSM Bed Leveling Utility by wileykyoto
by Thingiverse
Last crawled date: 3 years, 1 month ago
This is a quick Gcode script for bed leveling on the Monoprice Select Mini. It finds home then steps through 5 positions, waiting for 5(or 2) seconds at each spot to test the clearance. The position it steps through are: Front Left (5,5), Back Left (5,115), Back Right (115,115), Front Right (115,5), and Center (60,60).
There are two versions:
Utility_Bed_Leveling.gcode (5s pause and 80mm/s movement)
Utility_Bed_Leveling_Quick_2s.gcode (2s pause and 100mm/s movement)
To use this script, first make sure there's no filament on the outside of your nozzle. Then put a piece of A4 paper on the build plate. Run the print, and at each of the 5 locations test the fit by trying to slide the paper around. Then after all 5 positions have been done, adjust the four corners. Then run it again and repeat until you're happy with the fit.
I like to adjust the fit so that there is definitely some resistance when moving the paper around but not so much that it leaves an obvious mark/gouge on the paper. But the exact fit will depend on how thick your paper is.
To adapt this to other printers/configurations you will have to change the 5 positions to correspond to your build volume and screw locations. Ex: "G1 X5 Y5; (Position 1)" moves to x=5mm and y=5mm. You will also have to check the Gcode variant that your printer runs and check that all the commands are supported. You can also adjust the pause time by changing the delay in the pause commands. Ex: "G4 P5000; (Pause 1)" Pauses for 5000 miliseconds. You can change the movement speed by changing the feed rate set at the beginning. Ex "G1 F4800 Z1;" Sets the feed rate to 4800mm/min before issuing the first move command.
Happy Printing!
There are two versions:
Utility_Bed_Leveling.gcode (5s pause and 80mm/s movement)
Utility_Bed_Leveling_Quick_2s.gcode (2s pause and 100mm/s movement)
To use this script, first make sure there's no filament on the outside of your nozzle. Then put a piece of A4 paper on the build plate. Run the print, and at each of the 5 locations test the fit by trying to slide the paper around. Then after all 5 positions have been done, adjust the four corners. Then run it again and repeat until you're happy with the fit.
I like to adjust the fit so that there is definitely some resistance when moving the paper around but not so much that it leaves an obvious mark/gouge on the paper. But the exact fit will depend on how thick your paper is.
To adapt this to other printers/configurations you will have to change the 5 positions to correspond to your build volume and screw locations. Ex: "G1 X5 Y5; (Position 1)" moves to x=5mm and y=5mm. You will also have to check the Gcode variant that your printer runs and check that all the commands are supported. You can also adjust the pause time by changing the delay in the pause commands. Ex: "G4 P5000; (Pause 1)" Pauses for 5000 miliseconds. You can change the movement speed by changing the feed rate set at the beginning. Ex "G1 F4800 Z1;" Sets the feed rate to 4800mm/min before issuing the first move command.
Happy Printing!
Similar models
thingiverse
free
Python script to insert gcode commands before a layer by arpruss
...a simple python script to automate this and other similar things (e.g., inserting a temperature change). here it is...
thingiverse
free
Ø50mm bushing for 6301z bearing by improprietary
...lidworks part file, in here it is also
possible to change the tolerances of the bearing, diameter of the rod and the
resting lip.
thingiverse
free
Multi-Coloured Owl Key Tag by danricho
...f }}{% endif %}
{% endif %}
hope this was interesting/helpful.
i'm australian, so "colour" is the correct spelling!
thingiverse
free
Drawbot Inkscape GCode Exporter plugin by jbooblian
...time]
note: the model uploaded is just a stand-in to make this a valid remix [even though it's only really for a python file]
thingiverse
free
SN04 Sensor holder for ANET A8 by AUREL_14
...is command: m851 z-x.xx where x.xx is the noted value.
in a terminal, send this command: m500 (to sauve the offset in the eeprom)
thingiverse
free
Bed Leveling Script for Ultimaker by greengiant83
...h the same thing as the bed leveling wizard in cura except that you don't have to connect the printer to a computer to run it
thingiverse
free
Ender 3 v2 Dial indicator mount by StruikRover
...on.
notes
no auto home crash
no need for dissemble the mount
enjoy your flat bed :)
please note this designed for ender 3 v2
thingiverse
free
Timelaps set up for Flashforge creator pro by MikkelSimon
...bsolute positioning
g1 f9000 x-100 y71; quick move
g1 f1000 x-115; precission poke
g4 p700; hold it on
g1 f9000 x-100; quick move
thingiverse
free
ATOMIC Mahjong Card (filament color change)
... slicers pause command as a starting point and modify it as described below using gcode commands suitable for your printer
enjoy.
thingiverse
free
1984 Ingsoc logo by Kvant
...warning: watch your printer durring the first mutlicolor print. also, i have no responsibility for possible damage on your print.
Wileykyoto
thingiverse
free
Monoprice Select Mini Wire Brace by bradyhuutch
...your makes! the original designs can be found below. wileykyoto https://www.thingiverse.com/thing:2710870 janbbeck:...
thingiverse
free
monoprice select mini V2 bowden tube stabilizer
...bowden extruder with mpsm v2 improved extruder (wk9) by wileykyoto and it works great as well as adding capricorn...
thingiverse
free
Side panel for Monoprice Mini with cable routing
...abs filament inside a spiral cable wrap. added on wileykyoto#39;s excellent mpsm wire brace and had a really nice,...
thingiverse
free
40mm Fan Cover (20mm and 10mm Height) by wileykyoto
...lls. i printed it with a layer height of 0.175mm. i also recommend printing this upside down, so you don't need any supports.
thingiverse
free
MPSM Fully Adjustable Z Spacer (MP Select Mini) by wileykyoto
...t some point (around 0.7mm on my printer) the limit switch will slip off the end of the spacer and effectively act as 0mm offset.
thingiverse
free
MPSM V2 Improved Extruder (WK9) by wileykyoto
...s:
shout out to robin7331 and his mpsm extruder baseplate v1 for the idea to make a slot for a nut to work with a pc4-m6 fitting.
thingiverse
free
MPSM Wire Brace by wileykyoto
...ll do just fine.
update 2017-12-14
added a version with the wire brace centered.
added a version with the wire brace on the left.
thingiverse
free
MPSM V2 Extruder (Outdated See Decription) by wileykyoto
...s:
shout out to robin7331 and his mpsm extruder baseplate v1 for the idea to make a slot for a nut to work with a pc4-m6 fitting.
thingiverse
free
Extruder base with filament filter by Scanjo
...can either print the rest of the parts from wileykyoto#39;s thing, or modify a metal arm as i...
Mpsm
thingiverse
free
Z-height Shim Spacer for Monoprice Select Mini (MPSM) 1-10mm by monsieurglad
...nel (3 screws at top + 3 inside).
press-fit the size you need.
useful if you install a glass bed or hack the bed leveling system.
thingiverse
free
MPSM Fully Adjustable Z Spacer (MP Select Mini) - 10mm Longer by TheKrush
.../arm by 10mm to give clearance for https://www.thingiverse.com/thing:2006457 as i was noticing the dial hitting the spool holder.
thingiverse
free
Manual Bed Leveling Hack for Monoprice Select Mini MPSM by monsieurglad
...bwheel slides from the nut?: added a thicker thumbwheel so the nut will stop before falling. you can put a bit of crazy glue too.
thingiverse
free
3" PVC bulkhead by oredith
...it worked fine. this was designed around the monoprice mpsm so the print surface was pretty much limited to...
thingiverse
free
MPSM Spool holder with spindle by psfales
...acers to keep the spindle from rubbing on the bearing, and a flange to keep the spool from rubbing on the bearing or the holders.
thingiverse
free
Monoprice Select Mini V2 Gopro Mount by Astro_Mittens
...thingiverse simple design for taking time lapses on your mpsm ...
thingiverse
free
MPSM v3/Pro Manual Bed Leveling Hack + Test files by monsieurglad
...on to roughly level each corner with a post-it (0,1mm).
then i let the print go and level the other corners during live printing.
thingiverse
free
MPSM V2 Fan Duct 40mm by MysteriousMaker
...t be needed depending on how good your printer is at printing overhangs.
[updates]
added a high poly version (recommended to use)
thingiverse
free
Clip-on Carrying Handle for Monoprice Select Mini MPSM v1 v2 v3 by monsieurglad
...i v2 handle with hook: https://www.thingiverse.com/thing:2958205
large carrying handle: https://www.thingiverse.com/thing:3006746
thingiverse
free
MPSM Display Cover (Darkstar) by TerranStriker
...er
thingiverse
i made this for sleepies. just put it on the screen, don't force it in. enjoy! also i printed on a glass bed.
Utility
3d_export
$99
Chevrolet El Camino 1959 3D Model
...el camino 1959 1960 chevy 2-door coupe classic vintage utility pickup us american chevrolet el camino 1959 3d model...
3d_export
$99
MercedesBenz Sprinter Passenger Van 2014 3D Model
...mercedes-benz germany benz van minivan minibus passenger 2017 transport utility sprinter mercedesbenz sprinter passenger van 2014 3d model squir...
3d_export
$99
Chevrolet Colorado 2012 Extended Cab 3D Model
...2012 2013 2014 2015 pickup extended cab supercab usa utility chevrolet colorado 2012 extended cab 3d model squir 59279...
3d_export
$8
Cup Holder 3D Model
...cup holder 3d model 3dexport cup holder kitchen utility#39;s cup holder 3d model kingnin27 70463...
3d_export
$99
Toyota Tacoma Access Cab 2012 3D Model
...2012 2013 2014 2015 fl japan usa 4c4 offroad utility toyota tacoma access cab 2012 3d model squir 53144...
3d_ocean
$19
Penny farthing bicycle
...fast frame historical lady men netherlands roas street traditional utility vintage woman 3d model of penny farthing bicycle .object...
3d_ocean
$85
Vauxhall Vivaro Van 2015
...great high mini minivan model poly quality transport uk utility van vauxhall vehicle vivaro vauxhall vivaro van 2015 the...
3d_ocean
$85
Vauxhall Combo H2L2 Cargo 2015
...delivery england european h2l2 long minivan model transport uk utility van vauxhall vehicle wheel vauxhall combo h2l2 cargo 2015...
3d_ocean
$85
Vauxhall Combo Tour H1L1 2015
...england european h1l1 minivan model passenger tour transport uk utility van vauxhall vehicle vauxhall combo tour h1l1 2015 the...
3d_ocean
$85
Vauxhall Combo Tour H2L2 2015
...european h2l2 long minivan model passenger tour transport uk utility van vauxhall vehicle wheel vauxhall combo tour h2l2 2015...
Leveling
3d_export
$199
Stadium Level 6 Day 3D Model
...ty architecture element block gameready unity lowpoly football upgrade people
stadium level 6 day 3d model fabelar 90971 3dexport
3d_ocean
$12
Pterodactyl Base Mesh
...del is perfect for games and to start sculpting, ready for texturing and apply materials. created in / ready for zbrush 4r7 . ...
3d_ocean
$39
10 Frangipani Tree
...ormat obj file -10 frangipani tree style -4 polygon level of leaves (triangle count of your mesh) – high polygon 20205981 – me...
3d_ocean
$12
Spinosaurus Base Mesh
...del is perfect for games and to start sculpting, ready for texturing and apply materials. created in / ready for zbrush 4r7 . ...
3d_ocean
$29
Proto Cemetery Set
...ng blocks. they are meant to be used as a construction kit for rapid game prototyping. the blocks are real world scale and bui...
3d_ocean
$17
Old Water Tower
...nvironment. low poly triangles, and ready to be placed in your exterior level designs. textures is created using photoshop, an...
3d_ocean
$9
Bench park with 3 level detail of polygon
...f the same bench: 909 polygon with 1kmap, 5202 and 19508 polygon with 2kmap. each version is available in .fbx format and .obj...
3d_ocean
$12
Raptor Base Mesh
...del is perfect for games and to start sculpting, ready for texturing and apply materials. created in / ready for zbrush 4r7 . ...
3d_ocean
$7
Gas Station
...der, all movable parts are separated and can be rigged, has room inside with walls, doors etc. model is optimized and game ready.
3d_ocean
$12
Allosaurus Base Mesh
...del is perfect for games and to start sculpting, ready for texturing and apply materials. created in / ready for zbrush 4r7 . ...
Bed
design_connected
$29
Creed Bed
...creed bed
designconnected
minotti creed bed computer generated 3d model. designed by dordoni, rodolfo.
3d_export
$12
Bedside Table 3D Model
...odel
3dexport
bed bedroom table little small furniture 3ds wood wooden room textured
bedside table 3d model ikaras 90897 3dexport
3d_export
free
Download free Medical Examination Bed 3D Model
...al examination bed 3d model
3dexport
divan examination bed medical
medical examination bed 3d model dosoriofp78431 90995 3dexport
3d_export
$5
3d bed 3D Model
...3d bed 3d model
3dexport
3dsmax free3dmodel bed free download
3d bed 3d model free3dmodelss73900 90972 3dexport
3d_export
$8
ChiropractorTable 3D Model
...chiropractortable 3d model 3dexport medical doctor bones poser table bed 3d model hospital clinic office chiropractortable 3d model uncle808us...
3d_export
$15
Bed_2 3D Model
..._2 3d model
3dexport
bed living room sofas sofa armchair coffee table light carpet rug mat
bed_2 3d model dmyakotin 6968 3dexport
3d_export
$20
BED 1 3D Model
...bed 1 3d model
3dexport
bed girl's bedroom
bed 1 3d model corbu 32960 3dexport
3d_export
$8
Chair 3D Model
...furniture furnishing armchair bench modern table ergonomic orthopedic bed bedoom chair 3d model balatum 60743...
3d_export
$20
Furniture 3D Model
...furniture 3d model 3dexport bed chair dining table fridge furniture paintings sofa couch furniture...
3d_export
$39
Youyou09 3D Model
...bathroom bedroom bookroom kitchen table chair sofa dinner room bed mall youyou09 3d model future3d 65744...