Thingiverse
Embedded sliding front door for CraftBot by ckupcu
by Thingiverse
Last crawled date: 3 years ago
This space saving sliding front door is designed to nicely fit CraftBot's internal free space on the sides and bottom of the build plate. It is seen from outside only three transparent polystrerol plates and a thin handle to open/close. Design is assembled directly to CraftBot's original screws on the sides. Whole build volume is still accessible when the door is all the way down. When build plate is completely down, door can still be used without any problem.
Transparent plates are 365 x 88 mm2 with 2.3mm thickness. I did fine tune the dimensions of the plates and sliding links which hold them.
As a second option, you can have 4x 365 x 66 mm2 plates in the same rails. New Door_links_small_left_10.stl file contains new links for 66mm tall plates.
Refreshed *_10.stl files:
tested with CW 1.08 beta #10237 (PC) and CW 1.06 beta #4248 (Mac)
Improvements with *_10.stl
Door_rail_horizontal_left_10.stl file is updated, corner is lowered another 2mm so that last plate completely closes. Printed and in use already :-)
Contents of Door_rail_vertical_rail_10.stl and Door_links_left_10.stl are exactly same as *_9.stl. If you have already printed these two, no need to change.
New Door_links_small_left_10.stl file added. This contains links for 4 x 365 x 66 mm2 plates (to be printed...)
Improvements with *_9.stl:
Door plates height is reduced to 88mm. Links which hold door plates are also shortened 1mm to accommodate new plate height.
Horizontal rails are 4.5mm longer at the back. This will help door open another ~10mm down giving more access to the build volume.
Door handle is 2mm longer for better access, corners are nicely rounded to match CraftBot's corners ;-)
Remarks:
When opening the door, briefly push bottom plate's lower end with your finger while pushing down the door handle. You may need to do this every plate if you are opening the door slowly. In this way, you can stop the door at 3/4 different heights. If you open it a bit quicker, lower plates pull the others, hence door segments open all at once. Actually I did not design it to operate like this, but I kind of like this way. In my very first design, corners between vertical and horizontal rails were round. It was sliding much nicer, but plates were hitting CraftBot's rubber feet internal extensions (~5mm). To clear off feet extensions, I had to change it to a straight corner...
Transparent plates are 365 x 88 mm2 with 2.3mm thickness. I did fine tune the dimensions of the plates and sliding links which hold them.
As a second option, you can have 4x 365 x 66 mm2 plates in the same rails. New Door_links_small_left_10.stl file contains new links for 66mm tall plates.
Refreshed *_10.stl files:
tested with CW 1.08 beta #10237 (PC) and CW 1.06 beta #4248 (Mac)
Improvements with *_10.stl
Door_rail_horizontal_left_10.stl file is updated, corner is lowered another 2mm so that last plate completely closes. Printed and in use already :-)
Contents of Door_rail_vertical_rail_10.stl and Door_links_left_10.stl are exactly same as *_9.stl. If you have already printed these two, no need to change.
New Door_links_small_left_10.stl file added. This contains links for 4 x 365 x 66 mm2 plates (to be printed...)
Improvements with *_9.stl:
Door plates height is reduced to 88mm. Links which hold door plates are also shortened 1mm to accommodate new plate height.
Horizontal rails are 4.5mm longer at the back. This will help door open another ~10mm down giving more access to the build volume.
Door handle is 2mm longer for better access, corners are nicely rounded to match CraftBot's corners ;-)
Remarks:
When opening the door, briefly push bottom plate's lower end with your finger while pushing down the door handle. You may need to do this every plate if you are opening the door slowly. In this way, you can stop the door at 3/4 different heights. If you open it a bit quicker, lower plates pull the others, hence door segments open all at once. Actually I did not design it to operate like this, but I kind of like this way. In my very first design, corners between vertical and horizontal rails were round. It was sliding much nicer, but plates were hitting CraftBot's rubber feet internal extensions (~5mm). To clear off feet extensions, I had to change it to a straight corner...
Similar models
cults
free
CraftBot Hold Down Clip for PRINTinZ Plate
...bot hold down clip for printinz plate
cults
craftbot hold down clip for printinz plate
craftbot hold down clip for printinz plate
thingiverse
free
Sliding Door Handle by kspring
...ully open.
i'm new to 3d printing and design so, as always, my designs are a work in progress and can be edited if desired.
thingiverse
free
Corner Bracket
...h, 2020... let's see how it handles it.
dimensions:
back plate: 50x20x7 mm
top plate: 50x7x5 mm
holes: 5mm and 30 mm distance
thingiverse
free
Extruder Modifications for MM2 by dcgtek
...y line up with the aluminum holes better.
3) created a handle with thumb cutout for depressing the spring when changing filament.
grabcad
free
QUICK RELEASE LOCK V1.0
...ner hole in opened position and it will stay in its place. after the corners joined you just slide the handle to locked position.
3dwarehouse
free
open cw spiral slide 6'+ dh
...open cw spiral slide 6'+ dh
3dwarehouse
open cw spiral slide 6'+ dh
thingiverse
free
CraftBot Platform by 3DForms
... up proper print settings like hotend temp, bed temp, fan, layer height, print speed, retract settings, etc... for your filament.
cg_trader
$7
Olivari door handles set7
...olivari door handles set7
cg trader
set of 5 door handles olivari: open, icona, diva, beta, euclide
cg_trader
$6
Black Sliding Doors
...opened japan interior slide sliding rail 3dvm room home architectural door home interior interior room room interior sliding door
thingiverse
free
Sliding door handle by rawteq
... rawteq
thingiverse
created a handle to make it easier to open sliding doors when the wheel or slides get stuck or become tough.
Ckupcu
thingiverse
free
Envelope Opener by ckupcu
...atible with both german mozart/solingen and other standard single hole blades (see blue print) available in the market.
have fun!
thingiverse
free
CraftBot FLOW inside cabin filament holder and side panel holes by ckupcu
...ecial warp-free abs, prints like pla), you can of course print them in pla or abs - no problem. no special settings needed
enjoy!
thingiverse
free
Gear bearing filament roller for CraftBot by ckupcu
...ature:
ht: 215c
bt: 60c
gcode:
acceleration (postprocess gcode) enabled
supports: not needed
print time: <10h
filamet: <15m
thingiverse
free
Denon AH-D1100 Headphones - Earcup brackets with screw-less locking mechanism by ckupcu
...39;s one was broken while he was listening to music. i decided to make him happy again by 3d printing a much robust construction.
thingiverse
free
Custom Fan Ducts for CraftBot with circular cross section air nozzle by ckupcu
...ount
update:
added cb_fan_duct_both_with_raft.stl for abs printing with build in raft structures that you can cut afterwards.
Craftbot
thingiverse
free
TOESH - Totally overengineered spool holder for CraftBot Printers by AndreasALu
...nner diameter >17mm or whatever fits on your ball bearing) and a plastic pipe (length depending on the width of your printer).
thingiverse
free
Bed level test for Craftbot Flow XL by AndreasALu
...ns between the squares help removing the single layer print ;-) try lifting only one edge and you should be able to peel it away.
thingiverse
free
Bofa 50mm pipe to 80mm fan by philipsd
...an 80mm fan mount. i use this for my craftbot flow idex when printing...
thingiverse
free
CraftUnique CraftBot Flow Idex Spool / Filament Holder by Waggster
...thers)
i've included one the standard length and one 20mm longer.
printed in pla at 60% infill for strength at 0.16mm layers
thingiverse
free
CraftUnique CraftBot Flow Idex Filament PTFE Holder by Waggster
...or 0.2, 40% infill, pla will be fine.
ptfe 5mm tube just pushes in tight, tapered guide underneath to help load the filament in.
thingiverse
free
BLTouch pin holder for Craftbot Flow printers by AndreasALu
...ip.
don´t forget to take the holder off after the print, when you restart the printer or when you do mesh leveling / calibration!
thingiverse
free
TOESH - Totally overengineered spool holder for CraftBot Printers by AndreasALu
...nner diameter >17mm or whatever fits on your ball bearing) and a plastic pipe (length depending on the width of your printer).
thingiverse
free
Purge Bucket for Craftbot printer by Belezeebub
...purge bucket for craftbot printer by belezeebub
thingiverse
super fast purge bucket for craftbot flow or craftbot 3 printer
thingiverse
free
Craftbot Flow IDEX Rear Filament Mount Front Access with Dome by Waggster
...em. make sure you also print the guide and guide mount.
any comments or improvements that you can think of, please let me know.
thingiverse
free
TOESH - Totally overengineered spool holder for CraftBot Printers by AndreasALu
...nner diameter >17mm or whatever fits on your ball bearing) and a plastic pipe (length depending on the width of your printer).
Embedded
3ddd
$1
Wood Furniture by Greg Klassen
...greg klassen builds intricately designed tables and other objects embedded with glass rivers and lakes. inspired by his surroundings...
3d_ocean
$15
Honda Civic SI Lowpoly with HighRes Maps
...res maps builded in maya 8.5 ma format and also includes obj and fbx-fbx embeded textures formats. car body is 538 quad polygo...
3d_ocean
$5
Dust & Scratch Textures - A
...film surfaces. these scans reveal scratches and dust particles embedded in or sitting on 10 different 35mm...
3d_ocean
$5
Tarmac with Embedded Shells Seamless Texture
...mation. created from photographs. texture, displacement, normal, occlusion and specular jpg maps are all included in this down...
3d_ocean
$5
Animated Realistic Wooden Chest
...wooden chest 3d model with a camera animation and embedded a template in the chest, that you can use...
3d_ocean
$4
TEST TUBES
...science shader tests texture topology unwraped four test tubes embedded in its wooden base, with the colors of liquids...
3d_ocean
$9
Maxya - MEL Script Editor for Autodesk Maya
...maxya maya mel mel editor phyton scripter mel (maya embedded language) is the autodesk maya backbone native programming language....
3d_export
$15
CLamp 3D Model
...clamp 3d model
3dexport
lamp embeded design
clamp 3d model pknobloch 25653 3dexport
3d_export
$5
toaster
...for the grid where the slices of bread are embedded a galvanized steel (edited by the author himself) was...
3d_export
$9
modern velvet barrel chair low poly pbr
...fbx<br>gltf rar file contains velvet barrel chair model as embedded ...
Sliding
3d_ocean
$35
Playground Collection
...solution models. -the size is based on real world scale. -the .ma and .mb formats contain limitations and “set driven keys” th...
3ddd
$1
SISO - SLIDING DOOR SYSTEM
...siso - sliding door system
3ddd
sliding door system “mir” ss-304
sliding door system “mir” ss-304
size:(mm) 1900 x h1900
3d_export
$12
Wooden spiral staircase with slide 3D Model
...slide
wooden spiral staircase with slide 3d model download .c4d .max .obj .fbx .ma .lwo .3ds .3dm .stl armata2015 111117 3dexport
3ddd
$1
Seven Doors от Nendo - семь дверных конструкций
...en/works/seven-doors/?erelease
как всегда инструкция по использованию внутри архива. стек с turbosmooth не свернут.
3ddd
$1
i4 Marinari - Slide
...modern design sideboard from i4 marinari. i couldn't find any dimensions of the product, so i designed it to my needs.
enjoy.
3ddd
$1
Poltrona Frau JOBS
...cable management column, the top is equipped with a sliding door that allows access to a small compartment inside...
3ddd
$1
Giorgetti Tycoon Desk
...saddle leather, that have completely removable drawers with recessed sliding runners and silent system closing. a central sliding drawer...
3ddd
$1
Giorgetti Oro Tall Dresser-animated
... , oro
high poly model (1.800.000 polys)
animated to open (just slide the animation bar)
archive3d
free
Slide 3D Model
...ing playground swing seat
slide n100315 - 3d model (*.gsm+*.3ds) for exterior 3d visualization.
archive3d
free
Door 3D Model
...door 3d model archive3d door sliding door horizontal sliding door door s n150612 - 3d...
Front
3d_export
$15
Seats for car set 3D Model
...interior automobile leather vehicle detailed photorealistic racing sport bench front rear set vray seats for car set 3d model...
3d_export
free
Download free Robot Leg 3D Model
...robot machine mechanical leg shin light wave 3ds object front robotic robot leg 3d model sunnydk87 68894...
3ddd
$1
Hickory Chair Comode Artisan Curved Front Chest Ash
...korychair.com/furniture/living-room-den-and-foyer-furniture/1911-collection/i507619-artisan-curved-front-chest-ash.aspx
3d_ocean
$5
Front Desk
...front desk
3docean
desk front office reception
office reception counter or front desk. cad file and obj file included.
3ddd
$1
IinfraredRooms_Helo_HSI20
...111 cm - 4 heater elements, back area, sides, front / leg area for maximum exposure - heated benches...
3ddd
$1
Набор для интерьера от Worlds Away Homepage
...2 drawer mirrored side table with cross-hatch mirror drawer front and silver leaf base. dimensions: 23"w x 29"h x...
3ddd
$1
KARE Sideboard Gate 2 Doors 3 Drawer
...provide lots of storage space behind the ingeniously designed front gate is a real gem and an absolute highlight...
3ddd
$1
Poltrona Frau H_O
...in a colour matching the desk mat and the front of the drawer unit. on the side opposite the...
3ddd
$1
Poltrona Frau JOBS
...and a key lock on the outer side. the front of the drawer is upholstered with pelle frau ®...
3ddd
$1
Умывальник Superfront BLOCKS (Vray+Corona)
...а сайте
___________________________________
в архиве:
-файл 3ds max 2011 (vray)
-файл 3ds max 2011 (corona)
-fbx (vray)
-текстуры
Door
3d_export
$99
Buick Skylark convertible 1964 3D Model
...model 3dexport buick skylark 1964 1965 1966 1967 classic 2-door coupe sport convertible general motors us american buick skylark...
3d_export
$99
Suzuki Jimny 2013 3D Model
...3dexport suzuki jimny wide sierra 2013 2014 2015 2016 2-door suv crossover off-road 4x4 mini compact small japan japanese...
3d_export
$99
MercedesBenz EClass sedan W210 1996 3D Model
...w210 1996 1997 1998 1999 2000 2001 2002 2003 4-door sedan saloon luxury germany mercedesbenz eclass sedan w210 1996...
3d_export
$99
Chevrolet El Camino 1959 3D Model
...3d model 3dexport chevrolet el camino 1959 1960 chevy 2-door coupe classic vintage utility pickup us american chevrolet el...
3d_export
$99
Chevrolet Cruze hatchback 2012 3D Model
...2012 2013 2014 hatchback sport city urban style us door auto chevy compact family chevrolet cruze hatchback 2012 3d...
3d_export
$99
Renault Wind 3D Model
...roadster compact city sport eco car vehicle twingo concept door renault wind 3d model humster3d 33037...
3d_export
$99
Vauxhall Agila 2008 3D Model
...europe suzuki wagon r+ compact chevrolet mw city urban 5-door hatchback splash vauxhall agila 2008 3d model humster3d 46740...
3d_export
$15
Holland Architecture Door003 3D Model
...re medieval mediaeval romanesque gothic doric tuscan ionic minoan
holland architecture door003 3d model lotusmodel 47475 3dexport
3d_export
$99
Toyota Yaris 2012 5door 3D Model
...2012 5-door 5d 3d 3-door 2013 2014 2015 2016 hatchback japan small city car
toyota yaris 2012 5door 3d model squir 47702 3dexport
3d_export
$99
Audi R8 Coupe 2013 3D Model
...3d model 3dexport audi r8 2012 2013 2014 2015 2-door coupe sport luxury sportcar racing german germany audi r8...