Thingiverse
Druplicon by Graloth
by Thingiverse
Last crawled date: 3 years, 1 month ago
Update April 3. 2018: Added complete models of the druplicon at normal and 250% scale, in case anyone wants to print it with supports or similar.
I remixed @berkes model slightly, I wanted a pure Druplicon model that could be printed with no supports while still keeping a good quality.
The inner sphere was removed because the sphere that OpenSCAD generates is very low poly, which might not be very visible on the default scale, but once you scale it up it becomes very noticable. I can provide a version with a higher-poly inner sphere if people want.
First photo is of a 100% scale version, and a 150% scale version, if you scale the pins up the same amount, the clearance should stay the same.
The second photo is of my first version without the registration pins, which is why you might notice a slight misalignment of the two sides, the registration pins fixed this. (The white splotches are me using too much glue and getting my fingers stuck to parts of it :P )
I remixed @berkes model slightly, I wanted a pure Druplicon model that could be printed with no supports while still keeping a good quality.
The inner sphere was removed because the sphere that OpenSCAD generates is very low poly, which might not be very visible on the default scale, but once you scale it up it becomes very noticable. I can provide a version with a higher-poly inner sphere if people want.
First photo is of a 100% scale version, and a 150% scale version, if you scale the pins up the same amount, the clearance should stay the same.
The second photo is of my first version without the registration pins, which is why you might notice a slight misalignment of the two sides, the registration pins fixed this. (The white splotches are me using too much glue and getting my fingers stuck to parts of it :P )
Similar models
thingiverse
free
Gyroscopic Earring
...ding on slicer because it might not generate supports for the 2 cylinders, i printed it standing up and didn't need supports.
thingiverse
free
Princess Daisy Model by BSDCreates
...ng, i recommend reinforcing the umbrella first, either with permanent supports or in something like meshmixer, or blender.
enjoy!
thingiverse
free
Eagle Pin by DragonArtist15
... can be printed in any type of filament. i recommend slightly scaling up the model if you want the feather details to show more.
thingiverse
free
Guitar Bridge Pin by Dgarner5005
...first try but you might want to size it up a few percent. thanks for looking!
no support needed. printed mine at .2 layer height.
thingiverse
free
Filament guide
...bearing at. you will need 10 bb's for the bearing assembly. might want to print the pin on its side to keep it from breaking.
thingiverse
free
Impossible Sphere by th1nzz
...re by th1nzz
thingiverse
3d printed version of the wooden impossible sphere.
my first modelled 3d print i hope you guys like it.
thingiverse
free
Chubby Bunny by BoomBoomBrucey
...otos, which fits nicely in the hand.
i personally think it printed best using a raft and supports with an overhang support of 50.
thingiverse
free
chess piece by links1990
...chess piece by links1990
thingiverse
my chess piece i made in blender you might want to scale it up before printing
thingiverse
free
Druddha statue by pbuyle
...ammydavis. pop buddha by tamraz and druplicon by facine.
the word "drupal" is a registered trademark of dries buytaert.
thingiverse
free
Lego pencil holder
...int something useful, you must scale up the piece significantly. i printed this out as 90mm high version. see the attached photo.
Druplicon
thingiverse
free
Datsun merged with signal signal by shivinteger
...attribution - share alike [4] thing title : openscad druplicon ( a.k.a. the drupal logo ) [4] thing url...
thingiverse
free
Druddha statue by pbuyle
...druddha statue by pbuyle thingiverse druplicon headed buddha, the much needed statue for followers of...
thingiverse
free
Druplicon by KTHX
...rse
drupal is a trademark of dries buyaerthttp://drupal.com/trademark
this is a tribute to the best open source cms in the world
thingiverse
free
Dutch Druplicon by berkes
...ruplicon, the avatar of the famous open source cms drupal, wearing dutch clogs.
it was made for a conference in the netherlands.
thingiverse
free
OpenSCAD Druplicon ( a.k.a. the Drupal logo ) by sponnet
...e 25/10 : adapted the space around the eyes to make it more printable & rescaled it to fit a standard 10x10cm build platform.
Graloth
thingiverse
free
Bearing Spool Core by Graloth
...ave been updated.
the images might need to be updated in the future to reflect this change, as it was noticeable once i fixed it.
thingiverse
free
6201-2RS Bearing by Graloth
...hey are:
outer diameter: 32mm
inner diameter: 12mm
width: 10mm
i hope this will help someone as much as it has already helped me.
thingiverse
free
Knob handle for SpannerHans Spool System MK6 by Graloth
...ike how tinkercad had messed up the knobs geometry, so i redesigned it entirely in fusion360, used v1 to get the updated version.
thingiverse
free
Roller Bearing Core (EU Version) Bearing clearance fix by Graloth
...ak the tolerances for their printer or just want to remix it easier.
printing amount:
2x half-roll-v2.stl
6x registration-pin.stl
thingiverse
free
Prusa i3 MK3 PSU wall mount by Graloth
...ently adds some "fins" that aren't of much use for the bottom cover, so next update will likely be to remove those.
thingiverse
free
C270 X Motor Mount for Prusa MK3 by Graloth
... tightens against the motor.
thickness of part that sits against motor made to match thickness of motor mount, making them flush.
thingiverse
free
C270 Angled Camera Mount by Graloth
...own in the photos)
this is a simple remix that just makes the part that mounts to the motor or bed mount, have a 45 degree angle.
thingiverse
free
Logitech C270 adjustable focus ring knurled grip by Graloth
...ts taken from the focus ring stl files.
included is the finished stl file with better grip, as well as a step and fusion360 file.
thingiverse
free
14 "mini" 10mm dice box and tray, with ridges for easier opening by Graloth
...dges on the ends of the lid to allow for much easier separation of base and lid, as it allows for better grip on the base itself.
thingiverse
free
Drupal 8 Cookie Cutters by Graloth
...e the presses the full shape of the "8" into the cookie, making it easier to see if your dough rises a lot in the oven.